"Part " CNS Standards List |
|
CNS 60245-8
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 8: Cords for applications requiring high flexibility 額定電壓450/750 V 以下橡膠絕緣電纜－第8部：高可撓性用途花線 |
|
|
|
CNS 10785
2019 Edition Method of abrasion test for building materials and Part of building construction (Abrasive-paper method) 建築材料及建築組件磨耗試驗法(砂紙法) |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 61347-2-13
2019 Edition Lamp controlgear − Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules 光源控制裝置－第2-13部：LED模組用直流或交流電子式控制裝置之個別要求 |
|
|
|
CNS 15200-1-5
2019 Edition Testing methods for paints - Part 1-5 : General rule - Coating of test panel (brush application) 塗料一般試驗方法－第１－５部：通則－試驗板之塗裝（刷塗） |
|
|
|
CNS 15659-2
2019 Edition Evaluation of moisture-absorbing and quick-drying properties in textiles − Part 2: Moisture management test 紡織品吸濕速乾性能評估－第2 部：水分傳導試驗法 |
|
|
|
CNS 14253-2
2019 Edition Personal fall-arrest systems − Part 2: Lanyards and energy absorbers 個人擒墜系統−第2 部：繫索及能量吸收器 |
|
|
|
CNS 15646-1
2019 Edition Rigid cellular plastics – Determination of flexural properties – Part 1: Basic bending test 硬質發泡塑膠－彎曲性能測定法－第1 部：基本彎曲試驗 |
|
|
|
CNS 16121-1
2019 Edition Electrical apparatus for the detection of combustible gases in domestic premises − Part 1: Test methods and performance requirements 家居處所可燃氣體偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 15130-2-2
2019 Edition Tests on electric and optical fibre cables under fire conditions − Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame 電纜及光纜之燃燒試驗－ 第2-2部:單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 擴散火焰之程序 |
|
|
|
CNS 15762-5
2019 Edition Footwear − Test methods for uppers − Part 5: Thermal insulation of uppers, linings and insocks 鞋類－鞋面試驗法－第5 部：鞋面、內裡及鞋墊之隔熱性 |
|
|
|
CNS 13306-2-2
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power 射頻擾動和免疫力量測設備與量測方法－第２－２部：擾動和免疫力量測方法－擾動功率量測 |
|
|
|
CNS 15125-2
2019 Edition Solar heating - Domestic water heating systems - Part 2 : Outdoor test methods for system performance characterization and yearly performance prediction of solar-only systems 太陽能加熱－家用熱水系統－第２部：僅用太陽能系統的性能特性與年度性能預測之室外試驗法 |
|
|
|
CNS 62282-7-2
2019 Edition Fuel cell technologies − Part 7-2: Test methods − Single cell and stack performance tests for solid oxide fuel cells (SOFC) 燃料電池技術－第7-2部：試驗方法－固態氧化物燃料電池(SOFC)單電池及電池組性能試驗 |
|
|
|
CNS 15748-3
2019 Edition Integrated circuits − Measurement of electromagnetic emissions, 150 kHz to 1 GHz – Part 3: Measurement of radiated emissions – Surface scan method 積體電路－150 kHz 至1 GHz 電磁放射量測－第3 部：輻射放射量測－表面掃描法 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – Part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 15204-1
2019 Edition Leather − Chemical tests for the determination of certain azo colorants in dyed leathers − Part 1: Determination of certain aromatic amines derived from azo colorants 皮革－染色皮革中特定偶氮色料的測定法－第1部：測定偶氮色料衍生之特定芳胺 |
|
|
|
CNS 15077-6
2019 Edition Test conditions for machining centers - Part 6 : Accuracy of feeds, speeds and interpolations 切削中心機之檢驗條件－第６部：進給、速率與插值之精度 |
|
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability for wind turbine generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 60245-7
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − Part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 15755-5-7
2019 Edition Conversion tables for units − Part 5-7: Pressure or stress − Kilopascal and millimeter of water 單位換算表－第5-7 部：壓力或應力－千帕斯卡與毫米水柱 |
|
|
|
CNS 7779-3
2019 Edition Industrial fans – Determination of fan sound power levels under standardized laboratory conditions − Part 3: Enveloping surface methods 工業用風機－在標準化實驗室條件下風機聲功率位準測定－第3 部：包絡面法 |
|
|
|
CNS 15186-2
2019 Edition Cleanrooms and associated controlled environments – Part 2: Specifications for testing and monitoring to prove continued compliance with CNS 15186-1 潔淨室及其附屬之控制環境－第２部：確保持續符合ＣＮＳ １５１８６－１之測試與監測規範 |
|
|
|
CNS 8912
2019 Edition Method of abrasion test for building materials and Part of building construction (Method of abrasion test for flooring materials method with rotating disk fitted friction and impact) 建築材料及建築組件磨耗試驗法(旋轉圓盤之摩擦及衝擊地板材料之磨耗試驗法) |
|
|
|
CNS 15125-1
2019 Edition Solar heating - Domestic water heating systems - Part 1 : Performance rating procedure using indoor test methods 太陽能加熱－家用熱水系統－第１部：性能評比程序之室內試驗法 |
|
|
|
CNS 15077-4
2019 Edition Test conditions for machining centers - Part 4 : Accuracy and repeatability of positioning of linear and rotary axes 切削中心機之檢驗條件－第４部：線性軸與旋轉軸之定位精度與重現性 |
|
|
|
CNS 14873-3
2019 Edition Road vehicles - Airbag components - Part 3: Testing of inflator assemblies 道路車輛－氣囊組件－第３部：充氣器 |
|
|
|
CNS 7137
2019 Edition Sine-vibration testing method for automobile Parts 車輛零組件正弦振動試驗法 |
|
|
|
CNS 15660-3
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 3: Geometric tests for machines with inverted vertical workholding spindles 數值控制車床及車削中心機之試驗條件－ 第3部：倒立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 13306-1-5
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration test sites for 30 MHz to 1000 MHz 射頻擾動和免疫力量測設備與量測方法－第１－５部：射頻擾動和免疫力量測設備－30 MHz至 1000 MHz之天線校正場地 |
|
| Find out:2535Items | To Page of: First -Previous-Next -Last | [25] [26] [27] [28] [29] [30] [31] |
