"part " CNS Standards List |
|
CNS 7779-3
2019 Edition Industrial fans – Determination of fan sound power levels under standardized laboratory conditions − part 3: Enveloping surface methods 工業用風機－在標準化實驗室條件下風機聲功率位準測定－第3 部：包絡面法 |
|
|
|
CNS 15758-1
2019 Edition Packaging for terminally sterilized medical devices – part 1: Requirements for materials, sterile barrier systems and packaging systems 最終滅菌醫療器材之包裝－第1 部：材料、無菌屏障系統及包裝系統之要求 |
|
|
|
CNS 13306-1-1
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - part 1-1: Radio disturbance and immunity measuring apparatus - Measuring apparatus 射頻擾動和免疫力量測設備與量測方法－第１－１部：射頻擾動和免疫力量測設備－量測設備 |
|
|
|
CNS 15646-2
2019 Edition Rigid cellular plastics – Determination of flexural properties – part 2: Detrmination of flexural strength and apparent flexural modulus of elasticity 硬質發泡塑膠－彎曲性能測定法－第2 部：彎曲強度與視彎曲彈性係數測定法 |
|
|
|
CNS 15207-3
2019 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - part 3: Transverse electromagnetic (TEM) cell 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第３部：橫向電磁波室 |
|
|
|
CNS 14432-2
2019 Edition Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions − Method by analysis of evolved carbon dioxide − part 2: Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test 塑膠材料在控制堆肥條件下最終好氧生物分解度測定法－二氧化碳釋出量分析法－第2部：實驗室規模重量測定法 |
|
|
|
CNS 14705-3
2019 Edition Method of test for heat release rate for building materials − part 3: Guidance on measurement 建築材料燃燒熱釋放率試驗法－第3 部：量測之指引 |
|
|
|
CNS 15785-6
2019 Edition Tool holders with cylindrical shank − part 6: Type E with cylindrical seat 具圓柱柄之刀具夾持器－第6 部：具圓柱形座之E 型 |
|
|
|
CNS 15200-9-1
2019 Edition Methods of test for paints – part 9-1: Coating powders – Determination of gel time of thermosetting coating powders at a given temperature 塗料一般試驗法－第9-1 部：粉體塗料－指定溫度下熱固性粉體塗料膠化時間測定 |
|
|
|
CNS 16121-1
2019 Edition Electrical apparatus for the detection of combustible gases in domestic premises − part 1: Test methods and performance requirements 家居處所可燃氣體偵測用之電氣裝備－第1部：試驗方法及性能要求 |
|
|
|
CNS 15593-21
2019 Edition Electricity metering − Data exchange for meter reading, tariff and load control − part 21: Direct local data exchange 電力計量－讀表、計費及負載控制之資料交換－第21 部：直接本地資料交換 |
|
|
|
CNS 15449-2-101
2019 Edition Safe requirements for electrical for measurement, control and laboratory use ? part 2-101: Particular requirements for in vitro diagnostic (IVD) medical equipment 量測、控制及實驗室使用電氣設備安全規定－第2-101 部:體外診斷(IVD)醫用設備之個別規定 |
|
|
|
CNS 15755-2-3
2019 Edition Conversion tables for units − part 2-3: Length − Kilometer and nautical mile 單位換算表－第2-3 部：長度－公里與海里 |
|
|
|
CNS 16094-1
2019 Edition Ductile iron pipes, fittings, accessories and their joints − External zinc-based coating − part 1: Metallic zinc with finishing layer 延性鑄鐵管、管件、配件及接頭－外部鋅基塗層－第1部：金屬鋅及精整層 |
|
|
|
CNS 15209-2
2019 Edition Information technology –Home Electronic System (HES) Interfaces –part 2: Simple Interface (SI) Type 1 資訊技術－家庭電子系統介面－第２部：簡單介面型式１ |
|
|
|
CNS 15199
2019 Edition Electrical installations of buildings - part 7-712: Requirements for special installations or locations - Solar photovoltaic (PV) power supply systems 建築物之電力安裝－第７－７１２部：特別設立或地點之要求－太陽光電電力供應系統 |
|
|
|
CNS 60245-7
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − part 7: Heat resistant ethylene-vinyl acetate rubber insulated ables 額定電壓450/750 V 以下橡膠絕緣電纜－ 第7部：耐熱乙烯-醋酸乙烯酯橡膠絕緣電纜 |
|
|
|
CNS 12514-7
2019 Edition Fire-resistance tests – Elements of building construction – part 7: Specific requirements for columns 建築物構造構件耐火試驗法－第7 部：柱特定要求 |
|
|
|
CNS 15590-5
2019 Edition Mechanical properties of fasteners made of carbon steel and alloy steel – part 5: Set screws and similar threaded fasteners with specified hardness classes – Coarse thread and fine pitch thread 碳鋼及合金鋼結件之機械性質－第5 部：規定硬度級數之固定螺釘及類似螺紋結件－粗螺紋及細螺紋 |
|
|
|
CNS 15593-51
2019 Edition Electricity metering – Data exchange for meter reading, tariff and load control – part 51: Application layer protocols 電力計量－讀表、計費及負載控制之資料交換－第51 部：應用層協定 |
|
|
|
CNS 15014-3
2019 Edition Software engineering - Product evaluation - part 3: Process for developers 軟體工程－產品評估－第３部：發展者過程 |
|
|
|
CNS 15125-1
2019 Edition Solar heating - Domestic water heating systems - part 1 : Performance rating procedure using indoor test methods 太陽能加熱－家用熱水系統－第１部：性能評比程序之室內試驗法 |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 5346-2
2019 Edition Plastics - Symbols and abbreviated terms - part 2: Fillers and reinforcing materials 塑膠－縮寫用語與符號（第３部：可塑劑） |
|
|
|
CNS 62933-4-1
2019 Edition Electrical energy storage systems (EESS) − part 4-1: Guidance on environmental issues − General specification 電能儲存系統(EESS)－第4-1 部：環境議題之指引－一般規定 |
|
|
|
CNS 14943
2019 Edition Essential oils – General guidance on chromatographic profiles – part 1: Preparation of chromatographic profiles for presentation in standards 精油—層析特性成分分布通則－第1部：標準中層析特性成分分布之建立 |
|
|
|
CNS 15210-7
2019 Edition Information technology - Radio frequency identification for item management - part 7: Parameters for active air interface communications at 433MHz 資訊技術─品項管理之無線射頻識別─第７部：４３３ＭＨｚ主動式空中介面通信參數 |
|
|
|
CNS 15094-4
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - part 4: Removal of formaldehyde 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第4部：甲醛去除性能 |
|
|
|
CNS 15755-5-6
2019 Edition Conversion tables for units − part 5-6: Pressure or stress − Megapascal and kilogram-force per square centimeter 單位換算表－第5-6 部：壓力或應力－百萬帕斯卡與公斤力每平方公分 |
|
|
|
CNS 14498-1
2019 Edition Road vehicles - Electrical disturbances from conduction and coupling - part 1：Definitions and general consideration 道路車輛—經由傳導及耦合之電擾動－第1部：定義及通則 |
|
| Find out:2535Items | To Page of: First -Previous-Next -Last | [25] [26] [27] [28] [29] [30] [31] |
