"a, " CNS Standards List |
|
CNS 2958
2017 Edition Cast-iron Pipes and Fittings for Sanitary Equipments 衛生設備用鑄鐵管及管件 |
|
|
|
CNS 8917
2017 Edition Stationary Centrifugal Fire Pumps 固定式消防用加壓離心泵 |
|
|
|
CNS 2943
2017 Edition Screwed Type Malleable Cast Iron Pipe Fittings 螺紋式展性鑄鐵管件 |
Translated |
|
|
CNS 5277
2017 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 522
2017 Edition Snap Gauge for Whitworth Thread (Manufacturing Tolerance and Wear Limit) 韋氏螺紋量規（製造公差及損磨限） |
|
|
|
CNS 8784
2017 Edition Method of Test for Tensile of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管拉伸試驗法 |
|
|
|
CNS 9369
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 35 Proposed Insert Retention) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入扣鎖ＴＰ–３５） |
|
|
|
CNS 8697
2017 Edition Carbon Steel Plates for Pressure Vessels for Low Temperature Service 低溫壓力容器用碳鋼鋼板 |
|
|
|
CNS 12744
2017 Edition Wafer-Type Rubber-Seated Butterfly Valves 一般用蝶型閥 |
|
|
|
CNS 6135
2017 Edition Hearing aids-Part 0:Measurement of electroacoustical characteristics 助聽器－第０部:電聲特性的量測 |
|
|
|
CNS 13020
2017 Edition Method of Radoigraphic Test for the Welds of Steel Structure 鋼結構銲道射線檢測法 |
|
|
|
CNS 10461
2017 Edition Method of test for water repellency of textile fabrics - Spray test 織物撥水性試驗法－噴灑試驗 |
Translated |
|
|
CNS 4969
2017 Edition Band Saw Blades for Woodworking Machines 木工機械用鋸片帶 |
|
|
|
CNS 6408
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算–齒廓面作用帶因數Zн |
|
|
|
CNS 16016-1
2017 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PB) − Part 5: Fitness for purpose of the system 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第1部：通則 |
|
|
|
CNS 14466-7
2017 Edition Audiovisual,video and television equipment and systems. Part7:Safe handing and operation of audiovisual equipment 視聽．影像及電視設備與系統-第７部：視聽設備的安全搬運及操作 |
|
|
|
CNS 6135-12
2017 Edition Heading aids-Part12: Dimensions of electrical connector systems 助聽器－第12部:電氣連接系統之尺寸 |
|
|
|
CNS 12655
2017 Edition Construction of Pressure Vessels for Refrigeration 冷凍用壓力容器構造 |
|
|
|
CNS 4232
2017 Edition Torque Type Steel Hexagon Locknuts-Mechanical and Performance Properties 扭矩式六角防鬆鋼螺帽之機械性能及性質 |
|
|
|
CNS 12210
2017 Edition Method of Test for Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組檢驗法 |
|
|
|
CNS 459
2017 Edition Wood − Determination of longitudinal, radial and tangential shrinkage 木材尺度收縮率試驗法 |
|
|
|
CNS 11653
2017 Edition Method of Test for Glassfiber Reinforced Plastic Lamp Pole 玻璃纖維強化塑膠燈桿檢驗法 |
Translated |
|
|
CNS 3994
2017 Edition High Voltage Combination Starters 高壓綜合型起動盤 |
|
|
|
CNS 3883
2017 Edition Method of Test for Coating of Bicycle Parts 自行車（腳踏車）零件塗裝檢驗法 |
Translated |
|
|
CNS 5376-5
2017 Edition Iron ores—Methods for determination of total iron content 鐵礦石—總鐵定量法 |
|
|
|
CNS 7797
2017 Edition Thermal spraying - Zinc, aluminum and their alloys 鋅、鋁及其合金之熔射 |
|
|
|
CNS 8835
2017 Edition Methods of Test for Melting Point and Melting Range of Chemical Products 化學製品熔點及熔融範圍測定法 |
|
|
|
CNS 6106
2017 Edition Caps for Unplasticized Polyvinyl Chloride (UPVC) Conduit 帽套（硬質ＰＶＣ電線用管） |
|
|
|
CNS 13727
2017 Edition Method of Test for Volume Resistivity of Conductive Adhesives 導電膠之體積電阻率量測法 |
|
|
|
CNS 4306
2017 Edition Cross Recesses Countersunk (Flat) Head Tapping Screws 十字穴平頂埋頭自攻螺釘 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [299] [300] [301] [302] [303] [304] [305] |
