"C,E " CNS Standards List| Essential oils | Electrical Insulating | Indoor air | Method test | Method test | Reliability Assured | Terminology | Method Test | |
|
CNS 12886-1
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 120℃ or 150℃ 紙及紙板加速老化試驗法─120℃或150℃乾熱處理 |
Translated |
|
|
CNS 13350-7
2017 Edition The safety code of mechanical parking lot devices (elevators for car use) 機械式停車場（汽車用升降機） |
|
|
|
CNS 12564
2017 Edition Method of Test for Fiber Optic Devices (FOTP-172 Flame Resistance of Firewall Connector) 光纖裝置檢驗法（防火牆連接器之防火試驗ＦＯＴＰ–１７２） |
|
|
|
CNS 698
2017 Edition Method of Test for Activated Carbon (Power, for Industrial Use) 工業用活性碳（粉狀）檢驗法 |
|
|
|
CNS 4101
2017 Edition Pipe Couplings for Hydraulic Piping (Pipe Threads) 切管器 |
Translated |
|
|
CNS 16017
2017 Edition Rotodynamic pumps − Hydraulic performance acceptance tests − Grades 1, 2 and 3 迴轉動力泵液壓性能允收試驗－1級、2級及3級 |
|
|
|
CNS 996
2017 Edition Methods of test for resistance of glass containers to chemical attack 玻璃容器之耐化學侵蝕試驗法 |
|
|
|
CNS 14409
2017 Edition Sound and television broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measurement 聲音與電視廣播接收機及相關設備－免疫力特性－限制值與量測方法 |
Translated |
|
|
CNS 15523
2017 Edition Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs 機械安全—防止上肢及下肢觸及危險區域之安全距離 |
|
|
|
CNS 12664
2017 Edition Method of Test for Qualification Procedure of Welding Technique of Plastics 鑑定熔接塑膠技術之試驗法 |
|
|
|
CNS 15562-7
2017 Edition Stationary training equipment − Part 7: Rowing machines − Additional specific safety requirements and test methods 固定式訓練設備－第7部：划船機－附加之特定安全要求與試驗法 |
|
|
|
CNS 4939
2017 Edition Tar epoxy resin paint 環氧樹脂柏油漆 |
|
|
|
CNS 4224
2017 Edition Metric Trapezoidal Screw THread (Limits for Externational Screw Threads from 105 mm to 300 mm ) 梯形螺紋（標稱直徑１０５ｍｍ至３００ｍｍ的外螺紋限界尺寸） |
|
|
|
CNS 10849
2017 Edition Screw Threads of Valves for High Pressure Gas Cylider 高壓鋼瓶閥螺紋標準 |
Translated |
|
|
CNS 4225
2017 Edition Stub Metric Trapezoidal Screw Threads-Profiles 短梯形螺紋（螺紋輪廓） |
|
|
|
CNS 9705
2017 Edition General Rules for Emission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 664
2017 Edition Method of Test for Temperature of Transmission Shaft of Water Pumps 水泵傳動軸溫度檢驗法 |
|
|
|
CNS 9476
2017 Edition Test Code for Accuracy of Numerically Controlled Turret and Single Spindle Drilling Machines with Vertical Spindle 數值控制立式六角及單軸鑽床精度檢驗標準 |
|
|
|
CNS 15700-1
2017 Edition Plugs, socket-outlets, vehicle connectors and vehicle inlets − Conductive charging of electric vehicles − Part 1: General requirements 電源端插頭、電源端插座、車輛端插頭及車輛端插座－電動車輛傳導式充電－第1部：一般要求 |
|
|
|
CNS 101
2017 Edition Accuracy Inspection of Floor Type Horizontal Boring Machines 落地型臥式搪床精度檢驗 |
Translated |
|
|
CNS 10015
2017 Edition Glossary of terms relating to dynamic properties of vulcanized rubber 硫化橡膠動態性質用語 |
|
|
|
CNS 10901
2017 Edition Method of Test for Terminal Blocks for Industrial and Similar Use 工業用接線板檢驗法 |
|
|
|
CNS 6410
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算–小齒輪單齒接觸因數Ｚв 、大齒輪單齒接觸因數Ｚᴅ及正面接觸比 ε⍺ |
|
|
|
CNS 15285
2017 Edition General requirements and test methods for chargers used by mobile terminals and other hand-held ICT devices 用於行動終端及其他手持資通訊技術裝置之充電器一般規定及測試方法 |
|
|
|
CNS 66
2017 Edition Square Heads and Holes (for Shaft, Hand Wheel and Handles) 方頭及方孔（用於軸，手輪及手柄） |
|
|
|
CNS 12854
2017 Edition Fire Fighting Equipment for Liquefied Petroleum Gas Plant Use 液化石油氣設施用消防設備 |
|
|
|
CNS 11328
2017 Edition Sets of High Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件 |
|
|
|
CNS 4069
2017 Edition Pneumatic fluid power − General rules and safety requirements for systems and their components 氣動輪磨機 |
Translated |
|
|
CNS 8785
2017 Edition Method of Test for Electric Strength of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管絕緣強度試驗法 |
|
|
|
CNS 3886
2017 Edition Heat Treatment of Bicycle Parts 自行車（腳踏車）零件熱處理 |
Translated |
| Find out:15848Items | To Page of: First -Previous-Next -Last | [301] [302] [303] [304] [305] [306] [307] |
