"D C " CNS Standards List |
|
CNS 6102
2017 Edition Flush Plates for Indoor Use 室內用平面蓋板 |
|
|
|
CNS 4149
2017 Edition CanneD Chinese foods 中式食品罐頭 |
|
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 12292
2017 Edition Reliability Assured FixeD Carbon Composition Resistors (Established Failure Rate) 可靠度保證混合碳固定電阻器（故障率設定） |
Translated |
|
|
CNS 13195
2017 Edition Audio Recording - PCM Encoder/Decoder System 聲頻記錄（脈碼調變之編碼／解碼器系統） |
|
|
|
CNS 15481-5
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 5: Chemical loads 道路車輛－電機電子配備環境條件與試驗－第５部： 化學負載 |
|
|
|
CNS 5004
2017 Edition Reflex Reflectors for Pedal Bicycles 自行車（腳踏車）用反光板 |
Translated |
|
|
CNS 14384-3
2017 Edition Protective footwears ( replaced by CNS 20345 ) 化學藥品及微生物防護手套－抗化學藥品滲透性之測定 |
|
|
|
CNS 3673
2017 Edition Dimensions of Tires for Industrial Vehicles and Off Road Service 工業車輛及建設工程用輪胎之尺度 |
Translated |
|
|
CNS 12241
2017 Edition Steel Plates, Sheets for Layered Pressure Vessels 多層卷壓力容器用高張力鋼板及鋼帶 |
Translated |
|
|
CNS 4360
2017 Edition Slotted Pan Head Screws with Small Head 有槽小盤頭螺釘 |
Translated |
|
|
CNS 4364
2017 Edition Hexagon Head Fitting Bolts with Long Threaded Portion 六角頭配合螺栓（具長螺紋部份） |
|
|
|
CNS 10171
2017 Edition Method of 42 Percent Magnesium Chloride Stress Corrosion Test for Stainless Steels 不銹鋼之４２％氯化鎂應力腐蝕試驗法 |
|
|
|
CNS 5501
2017 Edition Self - Aligning Ball Bearings: Wide Inner Race, Inner Race with Clamping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 2863
2017 Edition Method of Test for Tolerances of Rolling Bearings 滾動軸承精度檢驗法 |
|
|
|
CNS 12085
2017 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求ＦＯＴＰ–５４） |
|
|
|
CNS 12547
2017 Edition Method of Tension Test for Front Fillet Welded Joint 前面填角熔接接合之拉伸試驗法 |
|
|
|
CNS 11646
2017 Edition Glassfiber reinforced plastic pipe for sewer and industrial use 污水與工業用玻璃纖維強化塑膠管 |
|
|
|
CNS 10237
2017 Edition Handles for Cranes 起重機用手柄 |
|
|
|
CNS 9467
2017 Edition Method Test for Test Device for Cylinder Pressure of Gasoline Engine 汽缸壓力試驗器檢驗法（汽油機用） |
|
|
|
CNS 140
2017 Edition Wrench, Socket-Headed (Wrench Opening Ranging From 41 to 145 mm) 套筒扳手（口寬自４１至１４５ｍｍ） |
Translated |
|
|
CNS 4097
2017 Edition Method of Test for Chuck of Portable Electric Drills 手提電鑽用夾頭檢驗法 |
Translated |
|
|
CNS 4744
2017 Edition C11 Type Connectors for Radio Frequency Coaxial Cables 射頻同軸Ｃ１１型連接器 |
|
|
|
CNS 4700
2017 Edition Hexagon Head Bolts with Thread Approximately to Head and with Small Widths Across Flats 六角頭全螺紋螺栓（具小對面寬度） |
|
|
|
CNS 14139
2017 Edition Measurement methods for the performance of transmitter and receiver modules used for wireless infrareD Communication 無線通信用紅外線傳輸和接收模組功能特性量測法 |
|
|
|
CNS 14367
2017 Edition Photography-Film dimensions-Micrographics 照相技術－軟片尺度－用於微縮技術之軟片 |
|
|
|
CNS 10116
2017 Edition Method for Determining Aluminium Content in Natural and Artificial Cryolte {Oxine (8-Hydroxyquinoline) Gravimetric Method} 天然及人造冰晶石中鋁定量法〔喔星 ( 8 - 羥基喹啉 ) 重量法〕 |
|
|
|
CNS 1187
2017 Edition Flat File for Carpenter, Wide Flat End 木工用闊平頭扁平銼 |
Translated |
|
|
CNS 13217
2017 Edition Cold Rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [301] [302] [303] [304] [305] [306] [307] |
