"D C " CNS Standards List |
|
CNS 6102
2017 Edition Flush Plates for Indoor Use 室內用平面蓋板 |
|
|
|
CNS 1187
2017 Edition Flat File for Carpenter, Wide Flat End 木工用闊平頭扁平銼 |
Translated |
|
|
CNS 5004
2017 Edition Reflex Reflectors for Pedal Bicycles 自行車（腳踏車）用反光板 |
Translated |
|
|
CNS 9359-18
2017 Edition Information technology - Vocabulary - Part 18: Distributed data processing 資訊技術－詞彙－第１８部：分散式資料處理 |
|
|
|
CNS 4569
2017 Edition T-Head Bolts with One-Rounded Head Ｔ形頭螺栓（具單邊圓角） |
|
|
|
CNS 14046
2017 Edition Environmental management − Water footprint − Principles, requirements and guidelines 環境管理－水足跡－原則、要求事項及指導綱要 |
|
|
|
CNS 6006
2017 Edition Dimensions of Hitch for Power Tillers 耕耘機用接頭 |
|
|
|
CNS 11712
2017 Edition Canned sweet corn 甜玉米罐頭 |
|
|
|
CNS 9467
2017 Edition Method Test for Test Device for Cylinder Pressure of Gasoline Engine 汽缸壓力試驗器檢驗法（汽油機用） |
|
|
|
CNS 6670
2017 Edition Method of Test for Methyl Ethyl Ketone by Gas Chromatography 丁酮氣相層析檢驗法 |
|
|
|
CNS 2863
2017 Edition Method of Test for Tolerances of Rolling Bearings 滾動軸承精度檢驗法 |
|
|
|
CNS 15481-5
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 5: Chemical loads 道路車輛－電機電子配備環境條件與試驗－第５部： 化學負載 |
|
|
|
CNS 13163
2017 Edition Method of Soundness Test for Fillet Welds 填角熔接部之無瑕疵試驗法 |
|
|
|
CNS 4364
2017 Edition Hexagon Head Fitting Bolts with Long Threaded Portion 六角頭配合螺栓（具長螺紋部份） |
|
|
|
CNS 240
2017 Edition Hand Reamers 手鉸刀 |
|
|
|
CNS 140
2017 Edition Wrench, Socket-Headed (Wrench Opening Ranging From 41 to 145 mm) 套筒扳手（口寬自４１至１４５ｍｍ） |
Translated |
|
|
CNS 13217
2017 Edition Cold Rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 3510
2017 Edition Copper anD Copper alloy covered electrodes 銅及銅合金被覆銲條 |
|
|
|
CNS 1188
2017 Edition Flat File for Carpenter, Sharp Flat End 木工用尖平頭扁平銼 |
Translated |
|
|
CNS 12085
2017 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求ＦＯＴＰ–５４） |
|
|
|
CNS 4665
2017 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 11646
2017 Edition Glassfiber reinforced plastic pipe for sewer and industrial use 污水與工業用玻璃纖維強化塑膠管 |
|
|
|
CNS 9107
2017 Edition Symbols of Connecting of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖連接類符號 |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 12547
2017 Edition Method of Tension Test for Front Fillet Welded Joint 前面填角熔接接合之拉伸試驗法 |
|
|
|
CNS 12241
2017 Edition Steel Plates, Sheets for Layered Pressure Vessels 多層卷壓力容器用高張力鋼板及鋼帶 |
Translated |
|
|
CNS 4700
2017 Edition Hexagon Head Bolts with Thread Approximately to Head and with Small Widths Across Flats 六角頭全螺紋螺栓（具小對面寬度） |
|
|
|
CNS 60335-2-42
2017 Edition Household and similar electrical appliances − Safety − Part 2-42: Particular requirements for commercial electric forceD Convection ovens, steam cookers and steam-convection ovens 家用和類似用途電器－安全性－第2-42部：商用強制對流烤箱、蒸汽鍋及蒸汽對流烤箱等電器之個別規定 |
|
|
|
CNS 4562
2017 Edition Cross Recessed Round Head Wood Screws 十字穴圓頭木螺釘 |
Translated |
|
|
CNS 12831
2017 Edition Welding terms 銲接詞彙 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [301] [302] [303] [304] [305] [306] [307] |
