"For " CNS Standards List| Sealants sealing | Respiratory protective | Edible Melon | Plastics | Sodium Metaperiodate | Etched Stem | Enclosed Sensitive | Canned chinese | |
|
CNS 6407
1984 Edition Calculation of Load Capacity For Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 5027
1984 Edition Control Timers For Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5026
1984 Edition Welding TransFormers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 5022
1984 Edition Thyristorstack For Welding Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears For Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5298
1984 Edition Hose Clamps For the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 10225
1984 Edition Test Code For Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 1419
1984 Edition Method of Test For Acetone 丙酮檢驗法 |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis For Pig Iron and Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 10502
1984 Edition Method For X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance For Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears For Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 8351
1983 Edition Test Code For Performance of Numerically Controlled Knee Type Vertical Milling Machine 數值控制膝型立式銑床動態檢驗法 |
|
|
|
CNS 8214
1983 Edition Testing Method of Outside and Inside Diameters Wrapped Bushes For Plain Bearing 滑動軸承用捲製軸承襯檢驗法(外徑及內徑) |
|
|
|
CNS 5521
1983 Edition Polyester Flims For Electrical Purposes 電器用聚酯膜 |
|
|
|
CNS 9475
1983 Edition Test Code For Performance of Numerically Controlled Turret and Single Spindle Drilling Machines with Vertical Spindle 數值控制立式六角及單軸鑽床動態檢驗法 |
|
|
|
CNS 6094
1983 Edition Entrance Caps For Rigid Steel Conduit 電線用鋼管進口蓋 |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys and Its Seat (For Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 3155
1983 Edition Chisels For Stone Work 石工鑿 |
|
|
|
CNS 5057
1983 Edition Feet with Thread For Jigs and Fixtures 具螺紋柄支腳（夾具用） |
|
|
|
CNS 4107
1983 Edition Flat Seal For Hydraulic Couplings 液壓接頭用扁封 |
|
|
|
CNS 4647
1983 Edition Square Taper Washers For High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 4692
1983 Edition Studs For Stud Welding with Tip Ignition; Unthreaded Studs 尖端燃熔用無螺紋樁 |
|
|
|
CNS 4691
1983 Edition Studs For Stud Welding With Tip Ignition; Threaded Studs 尖端燃熔用螺樁 |
|
|
|
CNS 7959
1983 Edition Method of Test For Stationary Governor Type Tachometers 固定調速式轉速計檢驗法 |
|
|
|
CNS 168
1983 Edition Tangential Key For Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 170
1983 Edition Flat Fitting Keys (For Thin Hub) 配合平鍵（用於薄轂） |
|
|
|
CNS 171
1983 Edition Screw and Hole For Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (For Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 8763
1983 Edition Method of Test For Micro Hardness Testing Machines for Vickers and Knoop Hardness 微小硬度試驗機檢驗法－維克氏硬度及克諾普硬度 |
|
| Find out:9607Items | To Page of: First -Previous-Next -Last | [303] [304] [305] [306] [307] [308] [309] |
