"In " CNS Standards List |
|
CNS 99
1993 Edition Accuracy Inspection of Slotting Machines 插床精度檢驗 |
Translated |
|
|
CNS 13213
1993 Edition Procedures for Temperature and Irradiance Corrections to Measured I-V Characteristics of CrystallIne Silicon Photovoltaic Devices 對矽晶光電元件之電流電壓特性測量值做溫度與輻射校正之程序 |
|
|
|
CNS 96
1993 Edition Test Code for Performance and Accuracy of Radial DrillIng Machines 旋臂鑽床精度檢驗與動態檢驗法 |
Translated |
|
|
CNS 4434
1993 Edition Round Nuts With Drilled Holes In One Face 頂孔圓螺帽 |
|
|
|
CNS 4433
1993 Edition Round Nuts With Set PIn Hole in Side 側孔圓螺帽 |
|
|
|
CNS 1326
1993 Edition Electrical Insulating Oils 電絕緣用油 |
Translated |
|
|
CNS 739
1993 Edition Method of Test for Rubber Inner Tubes for Bicycles 自行車用橡膠內胎檢驗法 |
|
|
|
CNS 13288
1993 Edition Basic Environmental TestIng Procedures Part 2: Tests - Guidance on Change of Temperature Tests 環境試驗法（電氣、電子）－溫度變化試驗之指引 |
|
|
|
CNS 3631
1993 Edition Basic Environmental TestIng Procedures Part 2: Tests - Test Q: Sealing 環境試驗法（電氣、電子）－密封性試驗法 |
|
|
|
CNS 3633
1993 Edition Basic Environmental TestIng Procedures Part 2: Tests, Test N: Change of Temperature 環境試驗法（電氣、電子）－溫度變化試驗 |
|
|
|
CNS 13165
1993 Edition Method of Macro Test for Section of Spot Welded JoInts 點熔接接合之斷面巨觀試驗法 |
|
|
|
CNS 13164
1993 Edition Method of Tension Shear Test for Spot Welded JoInts 點熔接接合之拉剪試驗法 |
|
|
|
CNS 94
1993 Edition Accuracy Inspection of Lathes 車床精度檢驗 |
Translated |
|
|
CNS 98
1993 Edition Accuracy Inspection of Shaping Machines 牛頭刨床精度檢驗 |
Translated |
|
|
CNS 97
1993 Edition Test Code for Performance and Accuracy of Double HousIng Type Planing Machines 門型龍門刨床精度檢驗與動態檢驗法 |
Translated |
|
|
CNS 4881
1993 Edition Tires for Industrial Vehicles and Off the Road Service 工業車輛及工程機械用輪胎 |
Translated |
|
|
CNS 95
1993 Edition Accuracy Inspection of Upright Drilling Machines 直立鑽床精度檢驗 |
Translated |
|
|
CNS 713
1993 Edition Cast iron flanged gate valves (10 kgf/㎠) (Inside screw non-rising stem type) 鑄鐵凸緣型閘閥(10 kgf/cm2)（閥桿非上升型） |
Translated |
|
|
CNS 13212
1993 Edition Surface Acoustic Wave (SAW) Resonators Part 1: General Information and Standard Values 表面聲波諧振器－第一部：一般性資訊及標準值 |
|
|
|
CNS 13195
1993 Edition Audio RecordIng - PCM Encoder/Decoder System 聲頻記錄(脈碼調變之編碼／解碼器系統) |
|
|
|
CNS 13196
1993 Edition SamplIng Rate and Source Encoding for Professional Digital Audio Recording 專業數位聲頻記錄之取樣率與聲源編碼 |
|
|
|
CNS 13197
1993 Edition DetermInation of the Image Distortion of Electro - Optical X - Ray Image Intensifiers 光電Ｘ射線影像加強器的影像失真之決定 |
|
|
|
CNS 13198
1993 Edition Fixed Multilayer Ceramic Chip Capacitors for Use In Electronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
|
|
|
CNS 12886-1
1993 Edition Method of Test for Accelerated AgIng of Paper and Paperboard - Dry Heat Treatment at 120℃ or 150℃ 紙及紙板加速老化試驗法－120 ℃或150 ℃乾熱處理 |
Translated |
|
|
CNS 13268
1993 Edition Test Methods for Performance and Accuracy of MouldIng Machine 多軸鉋機之性能試驗及精度檢驗法 |
|
|
|
CNS 12887-1
1993 Edition Method of Test for Accelerated AgIng of Paper and Paperboard - Moist Heat Treatment at 80℃ and 65% R.H. 紙及紙板加速老化試驗法－80 ℃及65 %R．H．濕熱處理 |
Translated |
|
|
CNS 13299
1993 Edition Method of Test for Trapezoid TearIng Strength of Geotextiles 地工織物撕裂強度試驗法（梯形法） |
|
|
|
CNS 13211
1993 Edition Audiovisual Equipment and System - RatIng Plates - Marking of Electricity Supply 視聽設備與系統之電源供應額定值面板標示 |
|
|
|
CNS 100
1993 Edition Accuracy Inspection of Table Type Horizontal Boring Machines 床台型臥式搪床精度檢驗 |
Translated |
|
|
CNS 853
1993 Edition Cross JoInts With Quadri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭(使用壓力16 kgf/cm2) |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [306] [307] [308] [309] [310] [311] [312] |
