"S " CNS Standards List |
|
CNS 506
2017 Edition ISO Metric Fine Screw Threads (Diameters from 70 to 300 mm and Pitch 6 mm) 公制細螺紋9（ISO制）（標稱直徑70至300公釐，螺距6公釐） |
|
|
|
CNS 5299
2017 Edition ASsembly tools for screws and nuts-Screwdriver bit for cross recessed head screws,with male hexagon drive 螺釘及螺帽之裝配工具–六角柄十字頭螺絲起子頭 |
|
|
|
CNS 12459
2017 Edition MethodS for determination of granulated (water quenched) blast-furnace slag, silica material, fly ash and limestone content in Portland cement and blended hydraulic cement 卜特蘭與水硬性混合水泥中水淬高爐爐碴、矽質材料、飛灰及石灰石含量之測定法 |
|
|
|
CNS 14282
2017 Edition ASsembly tools for screws and nuts - Four-way socket wrenches 螺釘及螺帽之裝配工具--十字形套筒扳手 |
|
|
|
CNS 4689
2017 Edition Studs for Drawn Arc Stud Welding Concrete Anchor and Shear Connectors 電弧樁熔接用柱樁–混凝土固定及剪力連接樁 |
Translated |
|
|
CNS 1358
2017 Edition Method of TeSt for Folding Endurance of Paper by Schopper type Tester 紙之蕭波式耐折強度試驗法 |
Translated |
|
|
CNS 3885
2017 Edition Method of TeSt for Surface Treatment of Bicycle Parts 自行車（腳踏車）零件表面處理檢驗法 |
Translated |
|
|
CNS 9476
2017 Edition TeSt Code for Accuracy of Numerically Controlled Turret and Single Spindle Drilling Machines with Vertical Spindle 數值控制立式六角及單軸鑽床精度檢驗標準 |
|
|
|
CNS 66
2017 Edition Square Heads and Holes (for Shaft, Hand Wheel and Handles) 方頭及方孔（用於軸，手輪及手柄） |
|
|
|
CNS 9
2017 Edition Zinc ingotS 鋅錠 |
|
|
|
CNS 2608
2017 Edition General RuleS for Inspection of Steel 鋼料之檢驗通則 |
|
|
|
CNS 1185
2017 Edition FileS (General) 銼（總則） |
Translated |
|
|
CNS 10779
2017 Edition Lighting of roadS for motor and pedestrian traffic 汽車及行人通行用道路照明 |
|
|
|
CNS 16016-1
2017 Edition PlaStics piping systems for hot and cold water installations − Polypropylene (PB) − Part 5: Fitness for purpose of the system 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第1部：通則 |
|
|
|
CNS 8068
2017 Edition Protective gloveS against mechanical risks 職業衛生用防護手套 |
Translated |
|
|
CNS 9969
2017 Edition Safety devices for protection against excessive pressure - Part 1: Safety valves 防止超壓之安全裝置－第1部：安全閥 |
|
|
|
CNS 3892
2017 Edition Hot rolled carbon Steel for cold-finished steel bars 光面鋼棒用熱軋碳鋼鋼料 |
|
|
|
CNS 5398
2017 Edition Clip for Wire Rope 鋼索夾 |
|
|
|
CNS 6407
2017 Edition Calculation of Load Capacity for Cylindrical and Bevel GearS-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算-負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 3884
2017 Edition Surface Treatment for Bicycle Parts 自行車（腳踏車）零件表面處理 |
Translated |
|
|
CNS 4579
2017 Edition Bolted ConnectionS with Reduced Body; Bolts 減徑柄螺栓之結合法（螺栓） |
|
|
|
CNS 5770
2017 Edition General Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 3005
2017 Edition Method of TeSt for Diesel Engine of Constant Speed 定速回轉柴油發動機性能檢驗法 |
|
|
|
CNS 7664
2017 Edition Method of TeSt for Low Frequency (Below 3 MHz)Electrical Connectors (TP - 25 Probe Damage Test) 頻率３ＭＨｚ以下電連接器檢驗法（探針損壞試驗ＴＰ–２５） |
|
|
|
CNS 3723
2017 Edition Method of teSt for milk and milk products - Determination of chloride content in edible cheese 乳品檢驗法－食用乾酪氯化物含量之測定 |
|
|
|
CNS 8910
2017 Edition MethodS of exposure to laboratory light sources for polymeric material of buildings 建築用聚合材料實驗室光源曝露試驗法 |
|
|
|
CNS 13215
2017 Edition BaSic Environmental Testing Procedures Part 2: Tests - Test Ed: Free Fall 環境試驗法（電氣、電子）–自然落下試驗法 |
|
|
|
CNS 13135
2017 Edition TeSt Methods for Performance and Accuracy of Band Saws and Feed Equipment 帶鋸機及送材裝置之試驗及檢驗法 |
|
|
|
CNS 15562-2
2017 Edition Stationary training equipment − Part 2: Strength training equipment − Additional specific safety requirements and test methods 固定式訓練設備－第2部：力量訓練設備－附加之特定安全要求與試驗法 |
|
|
|
CNS 3887
2017 Edition Method of TeSt for Heat Treatment of Bicycle Parts 自行車（腳踏車）零件熱處理檢驗法 |
Translated |
| Find out:16181Items | To Page of: First -Previous-Next -Last | [309] [310] [311] [312] [313] [314] [315] |
