"G " CNS Standards List |
|
CNS 5969
1985 Edition Bronze FlanGed Globe Valves (10kgf/c㎡) 青銅凸緣型球形閥(10 kgf/cm2) |
|
|
|
CNS 11353
1985 Edition Methods of Measurement for LiGht Source Colour 光源色之測定方法 |
|
|
|
CNS 5970
1985 Edition Bronze FlanGed Angle Valves (10kgf/c㎡) 青銅凸緣型角閥(10 kgf/cm2) |
|
|
|
CNS 5971
1985 Edition Bronze FlanGed Gate Valves (10kgf/c㎡) 青銅凸緣型閘閥(10 kgf/cm2) |
|
|
|
CNS 11232
1985 Edition LiGht-Exposure and Light-and-Water-Exposure Apparatus (Xenon-Arc Lamp Type) 氙弧燈式耐光性及耐候性試驗器 |
|
|
|
CNS 6415
1984 Edition Series of modules for StraiGht Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 2305
1984 Edition Asphalt LaminatinG Paper 夾層柏油紙 |
Translated |
|
|
CNS 11155
1984 Edition Grease Guns-Lever Type Hand Guns 手用槓壓式黃油槍及附件 |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of OrGanic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 6414
1984 Edition Basic Rack of StraiGht Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 11158
1984 Edition TunGsten-Carbide Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 4733
1984 Edition HexaGon Nuts with Collar 突緣六角螺帽 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for DrawinG Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 4732
1984 Edition Knurled Nuts with RinG 有環滾紋螺帽 |
|
|
|
CNS 5275
1984 Edition Base TanGent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5274
1984 Edition Base TanGent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 4730
1984 Edition LiftinG Eye Nuts 圓形環首螺帽 |
|
| Find out:10068Items | To Page of: First -Previous-Next -Last | [315] [316] [317] [318] [319] [320] [321] |
