"a, " CNS Standards List |
|
CNS 14801
2017 Edition Method of test for water resistance of material used in protective clothing (Impact penetration test) 防護衣材料防水性試驗法－衝擊穿透試驗 |
|
|
|
CNS 5968
2017 Edition Bronze Screwed Lift Check Valves (10kgf/c㎡) 青銅螺紋口升降型止回閥（10 kgf/㎠） |
|
|
|
CNS 4312
2017 Edition Clevis Pins with Heads Ｕ形環有頭插銷 |
|
|
|
CNS 4305
2017 Edition Cross Recesses Pan Head Tapping Screws 十字穴盤頭自攻螺釘 |
|
|
|
CNS 6677
2017 Edition Essential oils － Determination of ester values, before and after acetylation, and evaluation of the contents of free and total alcohols 精油－自由與總醇含量估計法（酯值測定法） |
|
|
|
CNS 9364
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 5 Contact Insertion and Removal Forces) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入、鬆脫及拔出力量ＴＰ–５） |
|
|
|
CNS 13982-3
2017 Edition Methods of test for bulk down and feather − Part 3: Composition (content analysis) 羽絨羽毛試驗法－第3部：組成 |
|
|
|
CNS 4482
2017 Edition Hexagon Socket Set Screws with Flat Point 六角承窩無頭平端固定螺釘 |
Translated |
|
|
CNS 15623
2017 Edition Paragliding equipment – Emergency parachutes – Safety requirements and test methods 飛行傘設備－緊急降落傘－安全要求與試驗法 |
|
|
|
CNS 8919
2017 Edition Auxiliaries of Stationary Centrifugal Fire Pumps 固定式消防用加壓離心泵之附屬裝置 |
|
|
|
CNS 13099
2017 Edition Austenitic Iron Castings 沃斯田體鑄鐵件 |
|
|
|
CNS 16015-1
2017 Edition Transportation of dangerous goods − Part 1: Requirement for the construction and testing of packagings 危險貨物之運輸－第1部：包裝物之構造與試驗要求 |
|
|
|
CNS 6508
2017 Edition Dairy ice cream (Packaged) 乳品冰淇淋(已包裝) |
|
|
|
CNS 1130
2017 Edition Pliers and nippers - Engineer's and lineman's pliers 夾鉗與剪鉗－一般技術要求 |
|
|
|
CNS 12846
2017 Edition Helium Mass Spectrometer Leak Testing by Trace Probe Method 氦質譜儀示蹤氣探針探漏法 |
|
|
|
CNS 4170
2017 Edition Short Pitch Transmission Precision Roller Chains and Chain Wheels 短節距精確傳動滾子鏈條及鏈輪 |
|
|
|
CNS 11155
2017 Edition Grease Guns-Lever Type Hand Guns 手用槓壓式黃油槍及附件 |
|
|
|
CNS 6678
2017 Edition Essential oils - Determination of carbonyl value - Free hydroxylamine method 精油－羰值測定法（自由羥胺法） |
|
|
|
CNS 7197
2017 Edition Basic Dimensions of 5 kgf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度（5 kgf/㎠） |
|
|
|
CNS 15481-4
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 4: Climatic loads 道路車輛－電機電子配備環境條件與試驗－第４部：氣候負載 |
|
|
|
CNS 5376-2
2017 Edition Iron ores—Method for determination of postassium content 鐵礦石—鉀定量法 |
|
|
|
CNS 5977
2017 Edition High - Speed Steel Blades for Machine and Shell Reamers with Screwed - on Blades 高速鋼刀片–螺釘固定式，機用鉸刀，殼形鉸刀 |
|
|
|
CNS 10114
2017 Edition Method for Determining Iron Content in Natural and Artificial Cryolite (1,10-Phenanthroline Photometric Method) 天然及人造冰晶石中鐵定量法（二氮雜菲吸光光度法） |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 1019
2017 Edition Picks (Single), One Taper End and One Hammershaped End 單十字鎬（僅具單一斜錐狀端部） |
|
|
|
CNS 4038
2017 Edition Parallel Bench Vices 鉗工虎鉗（圓膛定座式） |
Translated |
|
|
CNS 13334
2017 Edition Method of IZOD Impact Test for Rigid Plastics 硬質塑膠埃若德（ＩＺＯＤ）衝擊試驗法 |
Translated |
|
|
CNS 2936
2017 Edition Blackheart Malleable Iron Castings 黑心展性鑄鐵件 |
|
|
|
CNS 13154
2017 Edition Cold rolled special steel strips 冷軋特殊鋼鋼帶 |
|
|
|
CNS 257
2017 Edition Boiler Rivet Hole Reamer, with Square Head 鍋爐鉚釘孔鉸刀（方頭圓柱柄） |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [316] [317] [318] [319] [320] [321] [322] |
