"And " CNS Standards List |
|
CNS 9445-1
2020 Edition Sampling procedures for inspection by variables − Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic And a single AQL 計量值檢驗抽樣程序－第1部：單一品質特性與單一允收品質界限(AQL)逐批檢驗依AQL檢索之單次抽樣計畫 |
|
|
|
CNS 8411-2
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium And aluminium alloys - Part 2: Abrasive jet test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－第２部：噴射磨耗試驗法 |
|
|
|
CNS 154
2020 Edition Large Unfinished Washers (for Metric Bolts And Nuts: M6 - M52) 粗製大墊圈（用於公制螺栓及螺帽Ｍ６至Ｍ５２） |
Translated |
|
|
CNS 60669-2-1
2020 Edition Switches for household And similar fixed electrical installations − Part 2-1: Particular requirements − Electronic switches 家用和類似用途固定式電氣裝置之開關－第2-1 部：電子式開關之個別要求 |
|
|
|
CNS 15566-3
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 3: General principles for design And testing of pressure-sensitive bumpers, plates, wires and similar devices 機械安全－壓敏保護裝置－第3 部：設計及測試壓敏緩衝器、板、線及類似裝置之一般原則 |
|
|
|
CNS 61850-5
2020 Edition Communication networks And systems for power utility automation − Part 5: Communication requirements for functions and device models 電力公用事業自動化之通訊網路及系統－第5部：功能及裝置模型之通訊要求事項 |
|
|
|
CNS 3586
2020 Edition Perlite Heat Insulating Sheet (Block) And Pipe 真珠岩保溫板（磚）及保溫管 |
Translated |
|
|
CNS 15354
2020 Edition Test methods for dielectric strength of anodic oxide coatings on aluminium And aluminium alloys 鋁及鋁合金之陽極氧化膜絕緣性試驗法 |
|
|
|
CNS 532
2020 Edition Limits of Size And Tolerances for ISO Metric Coarse Screw Threads (Tolerance Quality:Fine,Tolerances:4H、5H and 4h)(Diameters from 1 to 68 mm and Pitches 0.25 to 6 mm) 公制粗螺紋限界尺寸及公差（ISO制）（細品級–4H、5H、4h）（標稱直徑1至68mm，螺距0.25至6mm） |
|
|
|
CNS 13875
2020 Edition Method of test for aluminum And silicon in fuel oils by ashing,fusion,inductively coupled plasma atomic emission spectrometry and atomic absorption spectrometry 燃料油中鋁及矽含量試驗法（灰化熔融感應耦合電漿原子放射光譜法及原子吸收光譜法） |
|
|
|
CNS 7070
2020 Edition Method of test for spices And condiments – Determination of moisture content – Entrainment method 香辛料及調味料之檢驗法－水分含量之測定(蒸餾法) |
|
|
|
CNS 3126
2020 Edition Bolts, Screws And Studs-Nominal Lengths, and Thread Lengths 螺栓、螺釘、螺樁之長度及螺紋長度 |
|
|
|
CNS 2393
2020 Edition Method of test for whiteness of white portlAnd cement 白色卜特蘭水泥白度檢驗法 |
|
|
|
CNS 14766
2020 Edition Method of test for water And sediment in middle distillate fuels by centrifuge 蒸餾油中水分及沉澱物測定法(離心法) |
|
|
|
CNS 4157
2020 Edition Metallic And other inorganic coatings – Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium 金屬及其他無機電鍍層－鎳、鎳鉻、銅鎳及銅鎳鉻電鍍層 |
|
|
|
CNS 62498-3
2020 Edition Railway applications − Environmental conditions for equipment − Part 3: Equipment for signalling And telecommunications 鐵路應用－設備之環境條件－第3部：號誌及電訊設備 |
|
|
|
CNS 62443-1-1
2020 Edition Industrial communication networks − Network And system security − Part 1-1: Terminology, concepts and models 工業通訊網路－網路及系統安全－第1-1部：術語、概念及模型 |
|
|
|
CNS 8992
2020 Edition Chemical Reagent (Fatty Oil, Fatty Acia And Higher Alcohol Determination) 化學試藥（油脂、脂肪酸及高級醇之檢驗） |
|
|
|
CNS 7030
2020 Edition Shapes And Dimensions of Fifth Wheel Coupling Pins for Semi-trailers 半拖車用第五輪聯結銷之形狀及尺度 |
|
|
|
CNS 15356
2020 Edition Test method for continuity of anodic oxide coatings on aluminium And aluminium alloys - Copper sulphate test 鋁及鋁合金之陽極氧化膜連續性試驗法－硫酸銅試驗法 |
|
|
|
CNS 2456-5
2020 Edition Plastics piping systems for water supply And for drainage and sewerage under pressure − Polyethylene (PE) − Part 3: Fittings 壓力下給水、排水及排污用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 14306-1
2020 Edition Preparation of steel substrates before application of paints And related products - Surface roughness characteristics of blast-cleaned steel substrates (Method for the calibration of ISO surface profile comparators and for the determination of surface pro 塗料及有關製品塗裝前之鋼面處理－噴射清理鋼面之表面粗糙度特性（磨料噴射清理表面評估用ISO表面輪廓參比標準板之規範及意義） |
|
|
|
CNS 15566-1
2020 Edition Safety of machinery – Pressure-sensitive protective devices – Part 1: General principles for design And testing of pressure-sensitive mats and pressure-sensitive floors 機械安全－壓敏保護裝置－第1 部：設計及測試壓敏墊及壓敏底板之一般原則 |
|
|
|
CNS 60669-2-6
2020 Edition Switches for household And similar fixed electrical installations – Part 2-6: Particular requirements – Fireman's switches for exterior and interior signs and luminaires 家用和類似用途固定式電氣裝置之開關－第2-6 部：外部與內部標誌及燈具用消防員開關之個別要求 |
|
|
|
CNS 530
2020 Edition Iso Metric Screw Threads-Tolerances-Limits of Sizes for Commercial Bolt And Nut Threads--Medium Quality 公制螺紋公差（ＩＳＯ制）（商用內、外螺紋之限界尺寸–中品級） |
Translated |
|
|
CNS 14596
2020 Edition Welding consumables − Gas shielded And self-shielded flux cored wires for arc welding of mild steel, high strength steel and low temperature service steel 銲接材料－軟鋼、高強度鋼及低溫用 鋼氣遮護及自遮護電弧銲接用包藥銲線 |
|
|
|
CNS 4446
2020 Edition Method of test for determination of water in petroleum products, lubricating oils, And additives by coulometric Karl Fisher titration 石油產品水含量測定法（Ｋａｒｌ Ｆｉｓｃｈｅｒ庫侖法） |
|
|
|
CNS 15692-3
2020 Edition Safety of machinery − Laser processing machines − Part 3: Noise reduction And noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2) 機械安全－雷射加工機－第3 部：雷射加工機、手持加工裝置及附屬輔助設備之噪音降低及噪音量測法(準確度等級2) |
|
|
|
CNS 14104-1
2020 Edition Prosthetics And orthotics - Classification and description of prosthetic components - Part 3: Description of upper-limb prosthetic components 義肢學與矯具學－肢體缺陷－第１部：先天性肢體缺陷之描述 |
|
|
|
CNS 9588
2020 Edition Kinds And Dimensions of Bases and Sockets of Electric Lamps for Automobiles 汽車用電燈泡燈頭及插座之種類與尺度 |
Translated |
| Find out:4887Items | To Page of: First -Previous-Next -Last | [28] [29] [30] [31] [32] [33] [34] |
