"In " CNS Standards List |
|
CNS 5501
1985 Edition Self - AlignIng Ball Bearings: Wide Inner Race, Inner Race with Clamping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 5505
1985 Edition Magneto Ball BearIngs 小電器用滾珠軸承 |
|
|
|
CNS 5504
1985 Edition Radial-Angular Contact Ball BearIngs, Single and Double-Row 徑向斜角接觸滾珠軸承（單列及雙列） |
|
|
|
CNS 5967
1985 Edition Bronze Screwed SwIng Check Valves (10kgf/c㎡) 青銅螺紋口擺動型止回閥(10 kgf/cm2) |
|
|
|
CNS 11290
1985 Edition Method of Test for Starch In Paper 紙中澱粉含量試驗法 |
Translated |
|
|
CNS 11328
1985 Edition Sets of High Strength Hexagon Bolt, Hexagon Nut and PlaIn Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件 |
|
|
|
CNS 4963
1985 Edition Test Code for Accuracy of Bench DrillIng Machines 枱式鑽床精度檢驗標準 |
Translated |
|
|
CNS 5500
1985 Edition Badial Self-alignIng Ball Bearings, Parallel and Tapered Bore 自動對位滾珠軸承（平行孔與推拔孔） |
|
|
|
CNS 11112
1984 Edition Methods of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 4660
1984 Edition Tommy Nuts with Fixed ClampIng Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 4659
1984 Edition Tommy Screws with Movable ClampIng Bolt 貫頭螺釘（滑動扳桿型） |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 4658
1984 Edition Tommy Screws with Fixed ClampIng Bolt 貫頭螺釘（固定扳桿型） |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears In the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities In Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and Sheated Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 5279
1984 Edition Dimensions of CylIndrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 5280
1984 Edition Helix Angles for CylIndrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-CuttIng Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 11094
1984 Edition Non-Thread TermInals 無螺紋端子 |
|
|
|
CNS 5285
1984 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 6777
1984 Edition Indoor Post Insulators 屋內柱形絕緣體 |
|
|
|
CNS 5283
1984 Edition Accuracy of CylIndrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 10868
1984 Edition Method of Test for SewIng Performance of Household Zig-zag Lock Stitch Sewing Machines 家庭用錯縱縫縫紉機縫製性能試驗方法 |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for CylIndrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 10898
1984 Edition Flat Quick-Connect TermInals 平板型接頭 |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for CylIndrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for DrawIng Instruments 滾紋螺帽（製圖儀器用） |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [325] [326] [327] [328] [329] [330] [331] |
