"T " CNS Standards List| Whitworth Thread | Canned vegetables | Dental Plaster | Fountain pens | Collar | Method test | Plastics | Chemical Reagent | |
|
CNS 502
2017 Edition ISO MeTric Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 8188
2017 Edition MeThod of Test for Water Retention by Concrete Curing Materials 混凝土養護材料保持水份能力檢驗法 |
|
|
|
CNS 3198
2017 Edition Silicon Sand (for CasTings) 矽砂（鑄造用） |
|
|
|
CNS 575
2017 Edition STeel bars for rivets 鉚釘用鋼棒 |
|
|
|
CNS 3124
2017 Edition Hexagon Head BolTs for Steel Structures 六角頭螺栓（鋼結構用） |
|
|
|
CNS 12867
2017 Edition Basic EnvironmenTal Testing Procedures Part 2 : Tests-Test Z/AM : Combined Dry Heat/Low Air Pressure Tests 環境試驗法（電氣、電子）–高溫／低氣壓複合試驗法 |
|
|
|
CNS 8918
2017 Edition Primary STandards ( replaced by CNS 12983 ) 固定式消防用加壓離心泵之原動機 |
|
|
|
CNS 14232-2
2017 Edition HealTh Level Seven (HL7) - Part 2: Control 健康資訊交換第七層協定－第２部：控制 |
|
|
|
CNS 10225
2017 Edition Test Code for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 10993
2017 Edition MeThods of Testing Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法（凹式） |
|
|
|
CNS 14109-3
2017 Edition Microfilming of Technical drawings and other drawing office documents--Part3:Unitized 35mm microfilm carriers 技術類製圖和其他規格化製圖文件之微縮─第三部: 填載35mm微縮軟片之孔卡 |
|
|
|
CNS 3135
2017 Edition Square Head BolTs (Semi-finished) 方頭螺栓（次精製） |
|
|
|
CNS 11223
2017 Edition MeThods for Chemical Analysis of Refractory Clay 耐火黏土化學分析法 |
|
|
|
CNS 2943
2017 Edition Screwed Type Malleable Cast Iron Pipe Fittings 螺紋式展性鑄鐵管件 |
Translated |
|
|
CNS 5650
2017 Edition MeThod of Test for Handy Lighter 瓦斯點火器檢驗法 |
|
|
|
CNS 8791
2017 Edition MeThod of Test for Low-Temperature Characteristics of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管低溫特性試驗法 |
|
|
|
CNS 10502
2017 Edition MeThod for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 11299-7
2017 Edition Glossary of Terms for sensing and transducing (Terms of measurement methods and equipment) 感測與轉換詞彙（有關量測方法與裝備名詞） |
|
|
|
CNS 12556
2017 Edition MeThod of Test for Thermal Performance for Solar Collectors 太陽能集熱器集熱性能檢驗法 |
|
|
|
CNS 4322
2017 Edition Hexagon BolTs with Thread Approximately to Head, Regular, Metric Thread 六角頭全螺紋螺栓（粗製） |
|
|
|
CNS 72
2017 Edition Taper Sleeve Wedge (for Cns125) 錐套分離楔（用於ＣＮＳ１２５） |
|
|
|
CNS 15329-7
2017 Edition InformaTion technology - Radio frequency identification device conformance test methods - Part 7: Test methods for active air interface communications at 433 MHz 資訊技術－無線射頻識別裝置符合性測試方法－第７部：４３３ＭＨｚ主動式空中介面通信之測試方法 |
|
|
|
CNS 11733
2017 Edition Rubber Threads 橡膠絲 |
|
|
|
CNS 4069
2017 Edition PneumaTic fluid power − General rules and safety requirements for systems and their components 氣動輪磨機 |
Translated |
|
|
CNS 9364
2017 Edition MeThod of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 5 Contact Insertion and Removal Forces) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入、鬆脫及拔出力量ＴＰ–５） |
|
|
|
CNS 9232
2017 Edition MeThod of Test for Dry Reed Switches(Preparation for Delivery) 乾式簧開關檢驗法（運送準備） |
|
|
|
CNS 4696
2017 Edition Round Head Nip BolTs 圓頭單鰭螺栓 |
|
|
|
CNS 10695
2017 Edition MeThod of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 10226
2017 Edition Test code for accuracy of wide belt sanders 寬帶砂光機精度檢驗 |
|
|
|
CNS 13069
2017 Edition MeThods of Test for Non-Volatile Matter in Solvent-diluted Epoxy Resins 溶劑稀釋型環氧樹脂不揮發分試驗法 |
|
| Find out:15111Items | To Page of: First -Previous-Next -Last | [326] [327] [328] [329] [330] [331] [332] |
