"T " CNS Standards List |
|
CNS 14492-3
2017 Edition MeThods of measurement on radio receivers for various classes of emission-Part3:Receivers for amplitude-modulated sound-broadcasting emissions 不同發射類別之無線電接收機的量測方法-第3部:調幅聲音廣播發射適用的接收機 |
|
|
|
CNS 123
2017 Edition MeTric Taper for Tools 9-200 (with Flat End) 工具圓錐（公制圓錐９–２００）（有扁頭） |
|
|
|
CNS 6004
2017 Edition AgriculTural Tactors and Machines-Symbols for Operator Controls 農業機械之操作標示符號 |
|
|
|
CNS 13624
2017 Edition Test Methods for Crystallographic Perfection of Gallium Arsenside by Molten Potassium Hydroxide(KOH)Etch Technique 砷化鎵晶體結晶完整性檢驗法（熔融氫氧化鉀浸蝕法） |
|
|
|
CNS 14139
2017 Edition MeasuremenT methods for the performance of transmitter and receiver modules used for wireless infrared communication 無線通信用紅外線傳輸和接收模組功能特性量測法 |
|
|
|
CNS 5517
2017 Edition Compression Terminals 壓縮端子 |
|
|
|
CNS 12085
2017 Edition MeThod of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求ＦＯＴＰ–５４） |
|
|
|
CNS 4660
2017 Edition Tommy Nuts with Fixed Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 11830
2017 Edition Measuring MeThods for Light Emitting Diodes (for Indication) 發光二極體(指示用)測量法 |
|
|
|
CNS 2205
2017 Edition CoTton Velvet and Cotton Corduroy Fabrics (Unfinished) 棉天鵝絨及棉燈芯絨（漂染前） |
|
|
|
CNS 13649
2017 Edition ReliabiliTy Testing for Laser Diode(for Communication) 通信用雷射二極體之可靠度測試 |
|
|
|
CNS 13198
2017 Edition Fixed MulTilayer Ceramic Chip Capacitors for Use in Electronic Equipment 電子設備用固定多層陶瓷晶片電容器 |
|
|
|
CNS 3443
2017 Edition MeThod of test for milk and milk products - Determination of moisture content 乳品檢驗法－水分之測定 |
Translated |
|
|
CNS 1098
2017 Edition Lumbar Saws for CarpenTer 木工用腰鋸 |
|
|
|
CNS 12297
2017 Edition MeThod of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP-15 Contact Strength) 頻率３ＭＨｚ以下電連接器檢驗法（接點強度ＴＰ–１５） |
|
|
|
CNS 4647
2017 Edition Square Taper Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 10746
2017 Edition CenTrifugally Cast Steel Pipes for High Pressure Service at High Temperature 高溫高壓用離心鑄鋼管 |
|
|
|
CNS 4364
2017 Edition Hexagon Head FiTting Bolts with Long Threaded Portion 六角頭配合螺栓（具長螺紋部份） |
|
|
|
CNS 13941
2017 Edition Micrographics-Microfilming of documenTs on 16mm and 35mm silver-gelatin type microfilm-Operating procedures 微縮技術–１６ｍｍ及３５ｍｍ銀鹽片之文件縮攝法–作業程序 |
|
|
|
CNS 10993
2017 Edition MeThods of Testing Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法（凹式） |
|
|
|
CNS 3992
2017 Edition High VolTage Alternating Current Starters 高壓交流起動器 |
|
|
|
CNS 6885
2017 Edition CasT Steel Flanged Swing Check Valves(10 kgf/㎠) 鑄鋼凸緣型擺動式止回閥（10 kgf/㎠） |
Translated |
|
|
CNS 6135-9
2017 Edition Hearing aids - ParT 9: Measurement of characteristics of hearing aids with bone vibrator output 助聽器－第9部:用骨導振動器輸出之助聽器性能特性的量測 |
|
|
|
CNS 7661
2017 Edition MeThod of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 22 Life Test) 頻率３ＭＨｚ以下電連接器檢驗法（壽命試驗ＴＰ–２２） |
|
|
|
CNS 3416
2017 Edition SafeTy Code for Power Presses (Definitions) 動力壓機安全規章（定義） |
|
|
|
CNS 10957
2017 Edition Test code for performance of circular sawing machines 圓鋸機動態檢驗法 |
|
|
|
CNS 12807
2017 Edition QualiTy Requirement for Microfilm of Documents and Drawings 微縮品製作–文件及圖面微縮軟片品質之要求 |
|
|
|
CNS 16015-1
2017 Edition Transportation of dangerous goods − Part 1: Requirement for the construction and testing of packagings 危險貨物之運輸－第1部：包裝物之構造與試驗要求 |
|
|
|
CNS 12996
2017 Edition MeThod of Determination for Contents of Metallic Elements of Hardmetals by X-Ray Fluorescence (Fusion Method) 超硬合金金屬元素含量測定法–Ｘ射線螢光分析法（熔融法） |
|
|
|
CNS 4320
2017 Edition Hexagon Head BolTs, Finished and Semi-Finished, Metric Fine Thread 六角頭螺栓（精製及半精制，公制細螺紋） |
|
| Find out:15111Items | To Page of: First -Previous-Next -Last | [329] [330] [331] [332] [333] [334] [335] |
