"o " CNS Standards List |
|
CNS 11582
2017 Edition Method of Test for Epoxy Resin Non-Zinc Primer 環氧樹脂非鋅底漆檢驗法 |
|
|
|
CNS 11223
2017 Edition Methods for Chemical Analysis of Refractory Clay 耐火黏土化學分析法 |
|
|
|
CNS 1196
2017 Edition Half-round File for Smith 鐵工用扁圓銼 |
Translated |
|
|
CNS 5508
2017 Edition Rolling Bearings; Bearings with Spherical Outside Surface and Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings 嵌入夾緊滾動軸承用壓製外殼 |
|
|
|
CNS 3422
2017 Edition oil-resistant Cork Sheet 耐油軟木板 |
|
|
|
CNS 13546-1
2017 Edition Plastics − Methods for determining the density of non-cellular plastics − Part 3: Gas pyknometer method 塑膠－聚甲基丙烯酸甲酯(PMMA)模製及押出材料－第1部：命名系統及分類基準 |
|
|
|
CNS 7642
2017 Edition Method of Test for Fiber Optic Devices (Air Leakage Testing of Fiber Optic Component Seals) 光纖裝置檢驗法（光纖組件密封漏氣試驗ＦＯＴＰ–２３） |
|
|
|
CNS 1411
2017 Edition Container for Lead Acid Batteries 鉛蓄電池用外殼 |
|
|
|
CNS 14447
2017 Edition Method of measurement for glossiness on surface of ornamental stone 天然飾面石材表面光澤度測定法 |
|
|
|
CNS 3453
2017 Edition Method of test for milk and milk products - Test of the residual antimicrobial substances in raw milk 乳品檢驗法－生乳中抗生物質殘留之檢驗 |
|
|
|
CNS 7167
2017 Edition Method of Test for Hydroxyl Value of Fatty Oils and Acids 脂肪油及脂肪酸羥價測定法 |
|
|
|
CNS 567
2017 Edition Hot Headed Rivet 熱作鉚釘 |
|
|
|
CNS 6090
2017 Edition Circular Surface Boxes for Rigid Steel Conduits 電線用鋼管圓形匣 |
|
|
|
CNS 6098
2017 Edition Couplings for Underfloor Duct 地板電線槽接頭 |
|
|
|
CNS 14046
2017 Edition Environmental management − Water footprint − Principles, requirements and guidelines 環境管理－水足跡－原則、要求事項及指導綱要 |
|
|
|
CNS 13656
2017 Edition Lot-Control Testing for Photodiode(for Communication) 通信用光二極體之批品質控制測試 |
|
|
|
CNS 13781
2017 Edition Endurance Testing Methods for Infrared Emitting Diodes (for Automation)-Burn-In Test (Forward Bias) 自動控制用紅外發光二極體耐久性試驗法–預燒試驗（順向偏壓） |
|
|
|
CNS 15322
2017 Edition Information technology - Radio frequency identification (RFID) for item management - Data Protocol : application interface 資訊技術－品項管理之無線射頻識別－資料協定：應用介面 |
|
|
|
CNS 15210-2
2017 Edition Information technology - Radio frequency identification for item management - Part 2: Parameters for air interface communications below 135kHz 資訊技術－品項管理之無線射頻識別－第２部：低於１３５ｋＨｚ空中介面通信參數 |
|
|
|
CNS 15524-4
2017 Edition Plastics - Determination of ash - Part 3: Unplasticized cellulose acetate 塑膠－灰分測定法－第4部：聚醯胺 |
|
|
|
CNS 14492-9
2017 Edition Methods of measurement on radio receivers for various classes of emission -Part 9：Measurement of the characteristics relevant to radio data system (RDS) reception 不同發射類別之無線電接收機的量測方法─第９部：無線電數據系統﹝RDS﹞接收相關特性值的量測 |
|
|
|
CNS 12437
2017 Edition Finishing Varnishes for Electrical Insulation 電絕緣用塗飾清漆 |
|
|
|
CNS 10698
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（靜音截斷、接收機動作及閉合時間） |
|
|
|
CNS 5969
2017 Edition Bronze Flanged Globe Valves (10kgf/c㎡) 青銅凸緣型球形閥（10 kgf/㎠） |
|
|
|
CNS 16009-7
2017 Edition Ladders − Part 7: Mobile ladders with platform 梯具－第7部：活動式工作平台梯 |
|
|
|
CNS 4423
2017 Edition Square Head Screws with Cone Point, M 5 to M 24 方頭錐形端螺釘（Ｍ５～Ｍ２４） |
|
|
|
CNS 7166
2017 Edition Method of Test for Color After Heating of Fatty Acids 脂肪酸加熱後之顏色檢驗法 |
|
|
|
CNS 4305
2017 Edition Cross Recesses Pan Head Tapping Screws 十字穴盤頭自攻螺釘 |
|
|
|
CNS 4704
2017 Edition Mounting Bolts and Wing Nuts for Watt-hour Meters 電錶裝置用螺栓與翼形螺帽 |
|
|
|
CNS 13513
2017 Edition Mortar for Unit Masonry 磚、石墁砌用墁料 |
|
| Find out:15086Items | To Page of: First -Previous-Next -Last | [331] [332] [333] [334] [335] [336] [337] |
