"A, " CNS Standards List| Multiple Ratio | Method test | In vitro | Method Test | Graphical Symbols | Fuel cell | Method Test | Method Test | |
|
CNS 4690
2017 Edition Studs for Drawn Arc Stud Welding - T - Studs 電弧樁熔接用柱樁–Ｔ形樁 |
|
|
|
CNS 1110
2017 Edition Method of Test for Hand Saws for Carpenter 木工用手鋸檢驗法 |
|
|
|
CNS 4660
2017 Edition Tommy Nuts with Fixed Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 7284
2017 Edition Methods for Determination of Gold and Silver in Sulphide Ores 硫化礦中金及銀定量法 |
|
|
|
CNS 5298
2017 Edition Hose Clamps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 8490
2017 Edition Strength Design Methods of Axles for Railway Rolling Stock 鐵路車輛用車軸強度設計方法 |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 13377
2017 Edition Boron Steel Wire Rods for Cold Heading and Cold Forging 冷打及冷鍛用硼鋼線料 |
|
|
|
CNS 12667
2017 Edition Method of Test for Qualification of Welding Procedure 熔接施工法之確認試驗法 |
|
|
|
CNS 15564-4
2017 Edition ISO general purpose metric screw threads - Tolerances - Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing ISO一般用途公制螺紋－公差－第4部：鍍鋅後依公差位置H或G攻牙之內螺紋相配合的熱浸鋅外螺紋之限界尺度 |
|
|
|
CNS 218
2017 Edition Counter-boring Drill with Morse Taper Shank （莫氏）推拔柄柱坑鑽頭 |
Translated |
|
|
CNS 6678
2017 Edition Essential oils - Determination of carbonyl value - Free hydroxylamine method 精油－羰值測定法（自由羥胺法） |
|
|
|
CNS 10169
2017 Edition Methods of Measuring Decarburized Depth for Steel 鋼之脫碳層深度測定法 |
|
|
|
CNS 4765
2017 Edition Method of Nitric-Hydrofluoric Acid Test for Stainless Steels 不銹鋼之硝酸–氫氟酸腐蝕試驗法 |
|
|
|
CNS 13350-6
2017 Edition The Safety Code of Mechanical Parking Lot Devices (Merry Goround Type) 機械式停車場安全標準〔方向轉換裝置（旋轉台）〕 |
|
|
|
CNS 12007
2017 Edition Method of Test for Helical Scanning Video Tape Recorders 螺線掃描錄放影機檢驗法 |
|
|
|
CNS 12844
2017 Edition Method of Test for Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布檢驗法 |
Translated |
|
|
CNS 4481
2017 Edition Hexagon Socket Set Screws with Cone End 六角承窩無頭錐形端固定螺釘 |
|
|
|
CNS 12077
2017 Edition Minimum Rounded Radii and Drafts of Hot Forging Closed Die 熱鍛閉合模之最小圓角半徑與拔模斜度（角度） |
|
|
|
CNS 13212
2017 Edition Surface Acoustic Wave (SAW) Resonators Part 1: General Information and Standard Values 表面聲波諧振器 第一部：一般性資訊及標準值 |
|
|
|
CNS 13216
2017 Edition Hot - rolled High Strength Steel Sheets with Improved Formability for Automobile Structural Uses 熱軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 12443
2017 Edition Polyacrylonitrile Staple Fibers (Shrinkable Type) 聚丙烯月青梭織物（漂染後） |
|
|
|
CNS 552
2017 Edition Pencil, coloured pencils and leads for them 鉛筆、顏色鉛筆及其筆芯 |
|
|
|
CNS 15513
2017 Edition Electric road vehicles – Reference energy consumption and range – Test procedures for passenger cars and light commercial vehicles 電動道路車輛－電能消耗與行駛距離－小客車與商用車試驗程序 |
|
|
|
CNS 12338
2017 Edition Crowbars 撬桿 |
|
|
|
CNS 6157
2017 Edition Method of Test for Electromechanical Switches(Monitoring Contact Chatter) 電機開關檢驗法–監測接觸齒震 |
|
|
|
CNS 15481-3
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 62351-2
2017 Edition Power systems management and associated information exchange − DatA and communications security − Part 10: Security architecture guidelines 電力系統管理及關聯資訊交換－資料及通訊安全－第2部：詞彙 |
|
|
|
CNS 12880
2017 Edition Cement Sack Paper Laminated with Plastic Woven Sheet 塑膠編織貼合水泥袋紙 |
Translated |
|
|
CNS 1224
2017 Edition Viscose Rayon Filament 黏液嫘縈絲 |
Translated |
| Find out:15242Items | To Page of: First -Previous-Next -Last | [332] [333] [334] [335] [336] [337] [338] |
