"T " CNS Standards List| Test Code | Test Code | Methods Test | Electric vehicle | 660V Single | Method Test | Methods test | Finishes Tolerance | |
|
CNS 14182
2017 Edition ReliabiliTy and lot control tests for analog video laser transmitter and receiver modules used for optical fiber communication 光纖通信用類比視訊雷射傳輸和接收模組之可靠度及批品質控制測試 |
|
|
|
CNS 10695
2017 Edition MeThod of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 1208
2017 Edition Heavy Triangular File for Smith 鐵工用重式三角銼 |
Translated |
|
|
CNS 1254
2017 Edition Canned pickled vegeTables 醬菜類罐頭 |
|
|
|
CNS 15481-3
2017 Edition Road vehicles - EnvironmenTal conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 13036
2017 Edition Liquefied PeTroleum Gas Pressure Regulator for Industrial Use 工業用液化石油氣壓力調整器 |
Translated |
|
|
CNS 1411
2017 Edition ConTainer for Lead Acid Batteries 鉛蓄電池用外殼 |
|
|
|
CNS 12716
2017 Edition Basic EnvironmenTal Testing Procedures - Part 2: Tests, Mounting of Components, Equipment and Articles for Dynamic Tests Including Shock (Ea), Bump (Eb), Vibration ( Fc and Fd ) and Steady - State Acceleration ( Ga ) and Guidance 環境試驗方法（電氣、電子）–動態試驗（包括衝擊、碰撞、振動及定加速度）之零組件、設備安裝方法及指南 |
|
|
|
CNS 7284
2017 Edition MeThods for Determination of Gold and Silver in Sulphide Ores 硫化礦中金及銀定量法 |
|
|
|
CNS 13143
2017 Edition MeThod of Test for Internal Bonding Strength Paperboard ( Using Z- direction Tensile / Compression Tester) 紙板內部結合強度試驗法（使用Ｚ–方向拉／壓式試驗機） |
Translated |
|
|
CNS 8490
2017 Edition STrength Design Methods of Axles for Railway Rolling Stock 鐵路車輛用車軸強度設計方法 |
|
|
|
CNS 5
2017 Edition Trimmed Sizes of Writing and Printing Paper 紙張尺度（裁切後） |
Translated |
|
|
CNS 4881
2017 Edition Tires for Industrial Vehicles and Off the Road Service 工業車輛及工程機械用輪胎 |
Translated |
|
|
CNS 4873
2017 Edition ElecTric Warm Pad 電暖墊 |
Translated |
|
|
CNS 15626-2
2017 Edition Ergonomic principles relaTed to mental workload - Part 2: Design principles 心智工作負荷相關之人因工程原理－第2部：設計原理 |
|
|
|
CNS 14382
2017 Edition ProTective gloces against chemicals and micro-organisms - Part 3:Determination of resistance to permeation by chemicals 防護手套－一般要求及試驗方法 |
|
|
|
CNS 11157
2017 Edition LubricaTion Holes, Grooves and Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 13252
2017 Edition MeThod of Tension Test for Spot Welded Joints 點熔接接合之拉伸試驗法 |
|
|
|
CNS 9363
2017 Edition MeThod of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 1 Acceleration) 頻率３ＭＨｚ以下電連接器檢驗法（加速力ＴＰ–１） |
|
|
|
CNS 12369
2017 Edition MeThod of Test for Fiber Optic Devices ( FOTP-45 Microscopic Method for Measuring Fiber Geometry) 光纖裝置檢驗法（測量光纖幾何之微觀方法ＦＯＴＰ–４５） |
|
|
|
CNS 510
2017 Edition Edison Thread 愛迪生式螺紋 |
|
|
|
CNS 552
2017 Edition Pencil, coloured pencils and leads for Them 鉛筆、顏色鉛筆及其筆芯 |
|
|
|
CNS 14694-1
2017 Edition Audio , video and audiovisual sysTems-interconnections and matching values Part 1：21-pin connector for video systems-application No.1 聲音、影像及視聽系統之互連與匹配值－第１部：影像系統適用之２１針連接器－第１類應用 |
|
|
|
CNS 13217
2017 Edition Cold Rolled High STrength Steel Sheets with Improved Formability for Automobile Structural Uses 冷軋高強度具成形性汽車結構用鋼片及鋼捲 |
|
|
|
CNS 4306
2017 Edition Cross Recesses CounTersunk (Flat) Head Tapping Screws 十字穴平頂埋頭自攻螺釘 |
|
|
|
CNS 3882
2017 Edition CoaTing for Bicycle Parts 自行車（腳踏車）零件塗裝 |
Translated |
|
|
CNS 9968
2017 Edition MeThod of Test for Drill Chuck for Machine Tools 工具機用鑽頭夾頭檢驗法 |
|
|
|
CNS 14685
2017 Edition Pulps - PreparaTion of laboratory sheets for measurement of reflectance 紙漿、紙及紙板表示性能之國際單位 |
|
|
|
CNS 744
2017 Edition Testing Standard for Rubber Rollers of Rice 碾米 |
Translated |
|
|
CNS 4843
2017 Edition Heavy Type Hexagon Head Pipe Plugs with Shoulder and Parallel Thread 重型六角頭管塞（具肩部與平行螺紋） |
|
| Find out:15111Items | To Page of: First -Previous-Next -Last | [333] [334] [335] [336] [337] [338] [339] |
