"or " CNS Standards List |
|
CNS 8672
1987 Edition Method of Test for Dry Reed Switches(Carry Current) 乾式簧開關檢驗法（負載電流） |
|
|
|
CNS 8221
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 32 Thermal Shock Test ) 頻率3 MHz以下電連接器檢驗法（熱震試驗TP-32） |
|
|
|
CNS 8670
1987 Edition Method of Test for Dry Reed Switches(Seals) 乾式簧開關檢驗法（密封） |
|
|
|
CNS 5770
1987 Edition General Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 8668
1987 Edition Method of Test for Dry Reed Switches(Vibration) 乾式簧開關檢驗法（振動） |
|
|
|
CNS 8667
1987 Edition Method of Test for Dry Reed Switches(Internal Moisture) 乾式簧開關檢驗法（內部潮濕） |
|
|
|
CNS 8230
1987 Edition Method of Test for Dry Reed Switches (Insulation Resistance) 乾式簧開關檢驗法（絕緣電阻） |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 8228
1987 Edition Method of Test for Dry Reed Switches (Dielectric) 乾式簧開關檢驗法（電介質） |
|
|
|
CNS 8227
1987 Edition Method of Test for Dry Reed Switches (Operation Parameters) 乾式簧開關檢驗法（動作參數） |
|
|
|
CNS 8226
1987 Edition Method of Test for Dry Reed Switches (Visual and Mechanical Inspection) 乾式簧開關檢驗法（目視與機械檢驗） |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality Assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 8224
1987 Edition Method of Test for Dry Reed Switches (General Rules) 乾式簧開關檢驗法（總則） |
|
|
|
CNS 8223
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 41 Circular Jacket Cable Flexing Test) 頻率3 MHz以下電連接器檢驗法（圓形護套電纜可撓性試驗TP-41） |
|
|
|
CNS 8222
1987 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connector (TP - 40 Crush Test) 頻率3 MHz以下電連接器檢驗法（軋壓試驗TP-40） |
|
|
|
CNS 10872
1987 Edition Method of Test for Fiber Optic Devices (FOTP-2 Impact Test) 光纖裝置檢驗法(撞擊試驗FOTP-2) |
|
|
|
CNS 8671
1987 Edition Method of Test for Dry Reed Switches(Contact Stickiness) 乾式簧開關檢驗法（接觸粘著性） |
|
|
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 11898
1987 Edition Reliability Assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 11904
1987 Edition Method of Test for Fiber Optic Devices (FOTP-81 Compound Flow (Drip) Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（有填充物光纜之化合物滴漏試驗FOTP-81） |
|
|
|
CNS 11905
1987 Edition Method of Test for Fiber Optic Devices (FOTP-83 Cable to Interconnecting Device Axial Compressive Loading) 光纖裝置檢驗法（光纜至連接器之軸向壓力負載FOTP-83） |
|
|
|
CNS 11906
1987 Edition Method of Test for Fiber Optic Devices (FOTP-84 Jacket Self-Adhesion (Blocking) Test for Fiber Optic Cable) 光纖裝置檢驗法（光纜被覆自黏性試驗FOTP-84） |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 12079
1987 Edition Method of Test for Digital Voltmeters 數字電壓計檢驗法 |
|
|
|
CNS 12077
1987 Edition Minimum Rounded Radii and Drafts of Hot Forging Closed Die 熱鍛閉合模之最小圓角半徑與拔模斜度(角度) |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 12076
1987 Edition Die Wear Tolerance for Hot Forging Closed Die 熱鍛閉合模之模具磨耗許可量 |
|
| Find out:10886Items | To Page of: First -Previous-Next -Last | [335] [336] [337] [338] [339] [340] [341] |
