"C " CNS Standards List |
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and related equipment 助聽器－第11部:助聽器及相關設備之符號及標示 |
|
|
|
CNS 4578
2017 Edition Bolted Connections with Reduced Booy; Metric Thread with Large Clearence, Nominal Values and Limits 減徑柄螺栓之結合法–具大間隙之公制螺紋（標稱尺寸與限界尺寸） |
|
|
|
CNS 4646
2017 Edition Square Taper Washers for High Prestressed I-SeCtions 斜墊圈（工字鐵高強度結構用） |
|
|
|
CNS 1021
2017 Edition PiCks, One Flat End and One Taper End 十字鎬（一端為尖錐狀，一端為鋼撬狀） |
|
|
|
CNS 13625
2017 Edition ProduCt analysis and its tolerance for wrought steel 圓形砷化鎵單晶片產品標準 |
|
|
|
CNS 6155
2017 Edition Method of Test for EleCtromechanical Switches(Actuator/Mounting Bushing Resistance) 電機開關檢驗法–主動器、裝架襯套電阻值 |
|
|
|
CNS 15624
2017 Edition Paragliding equipment – Harnesses – Safety requirements and strength tests 飛行傘設備─套袋─安全要求與強度試驗 |
|
|
|
CNS 13127
2017 Edition MetalliC and Other Non -organic Coatings -General Rules for Stationary Outdoor Exposure Corrosion Tests 金屬和無機被覆–靜態戶外曝露腐蝕試驗通則 |
|
|
|
CNS 407
2017 Edition Symbols of Transformers 變壓器符號 |
|
|
|
CNS 5376-4
2017 Edition Iron ores—Method for determination of Combined water content 鐵礦石—結合水定量法 |
|
|
|
CNS 5492
2017 Edition Thread Take-up Levers (Link Type) of Sewing MaChines for Inoustrial Use 工業用縫紉機連桿式挑線桿 |
|
|
|
CNS 13635
2017 Edition Steel Butt-welding Pipe Fittings for Ordinary Use 一般配管用鋼製對接銲接式管件 |
|
|
|
CNS 7178
2017 Edition ProteCtive gloves for occupational health 熔接用防護手套 |
|
|
|
CNS 10795
2017 Edition Insulation ResistanCe Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with SpheriCall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 5279
2017 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5293
2017 Edition Pressed Cement Roof Tiles (Arc-Pattern) 家庭用縫紉機壓布桿 |
|
|
|
CNS 5494
2017 Edition Needle Bar Connecting Links of Sewing Machines for Industrial Use 工業用縫紉機針棒連桿 |
|
|
|
CNS 400
2017 Edition Letter Symbols of EleCtricity 電量文字符號 |
|
|
|
CNS 6005
2017 Edition RiCe Hulling Rubber Rolls 礱穀機用橡膠滾筒 |
|
|
|
CNS 502
2017 Edition ISO MetriC Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 7149
2017 Edition Steel Castings for Low Temperature and High Pressure Service 低溫高壓用鑄鋼件 |
|
|
|
CNS 3183
2017 Edition Method of test for residues in liquefied petroleum gases 液化石油氣殘餘物試驗法 |
|
|
|
CNS 10000
2017 Edition Wire Ropes for MeChanical Control 機械控制用鋼纜 |
|
|
|
CNS 4896
2017 Edition ACcuracy Inspection of Metal Cutting Vertical Band Sawing Machines 立式帶鋸機精度檢驗標準 |
Translated |
|
|
CNS 9359-18
2017 Edition Information teChnology - Vocabulary - Part 18: Distributed data processing 資訊技術－詞彙－第１８部：分散式資料處理 |
|
|
|
CNS 9799
2017 Edition Stress and fatigue analyses for pressure vessels 壓力容器之應力解析及疲勞解析 |
|
|
|
CNS 258
2017 Edition Ring Gauge for Reamer 鉸刀校驗樣圈 |
|
|
|
CNS 4897
2017 Edition ACcuracy Inspection of Metal Cutting Horizontal Band Sawing Machines 臥式帶鋸機精度檢驗標準 |
Translated |
| Find out:16181Items | To Page of: First -Previous-Next -Last | [337] [338] [339] [340] [341] [342] [343] |
