"s " CNS Standards List |
|
CNS 1021
2017 Edition Picks, One Flat End and One Taper End 十字鎬（一端為尖錐狀，一端為鋼撬狀） |
|
|
|
CNS 4573
2017 Edition slotted Raised Countersunk Bolts for Drawing Instruments 有槽扁圓頂埋頭螺栓（繪圖儀器用） |
|
|
|
CNS 10000
2017 Edition Wire Ropes for Mechanical Control 機械控制用鋼纜 |
|
|
|
CNS 15520
2017 Edition Push and Pull Drain Trap (P Type) 建築物室內用補平塗材 |
|
|
|
CNS 4309
2017 Edition Conical spring Washers 圓錐彈簧墊圈 |
|
|
|
CNS 12886-1
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 120℃ or 150℃ 紙及紙板加速老化試驗法─120℃或150℃乾熱處理 |
Translated |
|
|
CNS 4250
2017 Edition square Head Screws with Collar and Half Dog Point with Rounded End Screws 軸環半柱端方頭螺釘 |
|
|
|
CNS 5666
2017 Edition spindle Noses for Milling Machines 銑床主軸鼻端 |
|
|
|
CNS 15604
2017 Edition Corrugated stainless steel tubes for water supply 自來水用不銹鋼波狀管 |
Translated |
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 5492
2017 Edition Thread Take-up Levers (Link Type) of Sewing Machines for Inoustrial Use 工業用縫紉機連桿式挑線桿 |
|
|
|
CNS 4797-5
2017 Edition Toy safety (Chemical Toys (Sets) Other Than Experimental Sets) 玩具安全（非實驗套組之化學玩具套組） |
Translated |
|
|
CNS 5669
2017 Edition Arbors for Milling Machines 銑刀心軸 |
|
|
|
CNS 13635
2017 Edition steel Butt-welding Pipe Fittings for Ordinary Use 一般配管用鋼製對接銲接式管件 |
|
|
|
CNS 5494
2017 Edition Needle Bar Connecting Links of Sewing Machines for Industrial Use 工業用縫紉機針棒連桿 |
|
|
|
CNS 4727
2017 Edition Power quality measurement in power supply systems − Part 1: Power quality instruments 動力插秧機 |
Translated |
|
|
CNS 225
2017 Edition shell Drills (Shell Counterborer) of High Speed Steel 殼形擴孔鑽 |
|
|
|
CNS 10795
2017 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 3183
2017 Edition Method of test for residues in liquefied petroleum gases 液化石油氣殘餘物試驗法 |
|
|
|
CNS 4646
2017 Edition square Taper Washers for High Prestressed I-Sections 斜墊圈（工字鐵高強度結構用） |
|
|
|
CNS 7149
2017 Edition steel Castings for Low Temperature and High Pressure Service 低溫高壓用鑄鋼件 |
|
|
|
CNS 13144
2017 Edition Method of Test for Internal Bonding Strength of Paper and Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法（使用抗張強度試驗機) |
Translated |
|
|
CNS 11829
2017 Edition Light Emitting Diodes (for Indication) 發光二極體(指示用) |
|
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part1:General considerations and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
|
|
|
CNS 502
2017 Edition IsO Metric Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 6632
2017 Edition Household polyvinyl chloride gloves 家庭用聚氯乙烯塑膠手套 |
|
|
|
CNS 400
2017 Edition Letter symbols of Electricity 電量文字符號 |
|
|
|
CNS 7178
2017 Edition Protective gloves for occupational health 熔接用防護手套 |
|
|
|
CNS 6005
2017 Edition Rice Hulling Rubber Rolls 礱穀機用橡膠滾筒 |
|
|
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and related equipment 助聽器－第11部:助聽器及相關設備之符號及標示 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [337] [338] [339] [340] [341] [342] [343] |
