"C,E " CNS Standards List |
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and related equipment 助聽器－第11部:助聽器及相關設備之符號及標示 |
|
|
|
CNS 219
2017 Edition Counter-boring Drill with Straight Shank 直柄柱坑鑽頭 |
Translated |
|
|
CNS 13350-7
2017 Edition The safety code of mechanical parking lot devices (elevators for car use) 機械式停車場（汽車用升降機） |
|
|
|
CNS 13046
2017 Edition General Rules of Chemical Analysis for Magnesium Alloys 鎂合金分析法通則 |
|
|
|
CNS 10868
2017 Edition Method of Test for Sewing Performance of Household Zig-zag Lock Stitch Sewing Machines 家庭用錯縱縫縫紉機縫製性能試驗方法 |
|
|
|
CNS 1131
2017 Edition Pliables plastic conduits (replaced by CNS 12152) 夾鉗與剪鉗－拔釘鉗 |
|
|
|
CNS 4300
2017 Edition Test Code for Accuracy of Surface Grinding Machines With Horizontal Grinding Wheel Spindle and Reciprocating Table 往復床台型臥式平面磨床精度檢驗標準 |
Translated |
|
|
CNS 14623-1
2017 Edition Sterilization of health care products-chemical indicators-Part 1：General requirements 保健產品之滅菌─化學指示劑─第一部分：一般規定 |
|
|
|
CNS 11829
2017 Edition Light Emitting Diodes (for Indication) 發光二極體(指示用) |
|
|
|
CNS 12070
2017 Edition Ejectorplate Guide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 8836
2017 Edition Method of Test for Freezing Point of Chemical Products 化學製品凝固點測定法 |
|
|
|
CNS 11942-8
2017 Edition Methods for determination of phosphorous in copper and copper alloys 銅及銅合金中磷定量法 |
|
|
|
CNS 15511-21
2017 Edition Electric vehicle conductive charging system – Part 21: Electric vehicle requirements for conductive connection to an a.c./d.c. supply 電動車輛傳導式充電系統－第21部：傳導式連接至a.c./d.c.電源之電動車輛要求 |
|
|
|
CNS 9907
2017 Edition Hard fiberboards 硬質纖維板 |
|
|
|
CNS 13622
2017 Edition Fixed chip resistor for use in electroniC Equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 3453
2017 Edition Method of test for milk and milk products - Test of the residual antimicrobial substances in raw milk 乳品檢驗法－生乳中抗生物質殘留之檢驗 |
|
|
|
CNS 7139
2017 Edition General Rules of Dust Test for Automobile Parts 汽車零件之防塵及耐塵試驗通則 |
|
|
|
CNS 4409
2017 Edition Screw and Washer Assemblies 套有墊圈之螺釘 |
|
|
|
CNS 13982-8
2017 Edition Methods of test for bulk down and feather − Part 8: Determination of fill power with steam conditioning 羽絨羽毛試驗法－第8部：蒸汽處理後蓬鬆度測定法 |
|
|
|
CNS 7281
2017 Edition General Rules for Determination of Gold and Silver in Ores 礦石中金及銀定量法總則 |
|
|
|
CNS 14137
2017 Edition Method of eddy current test for titanium pipes and tubes 鈦管渦電流檢測法 |
|
|
|
CNS 5203
2017 Edition Earth Testers 接地電阻測試計 |
|
|
|
CNS 5150
2017 Edition Photography-Processing chemicals -Specifications for hydroquinone 照相術─顯像處理化學品─對苯二酚規格 |
|
|
|
CNS 11573
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-50 Sand and Dust Test) 頻率３ＭＨｚ以下電連接器檢驗法（細砂與塵埃試驗ＴＰ–５０） |
|
|
|
CNS 295
2017 Edition Methods of Chemical Test for Braze 銲臘化學檢驗法 |
|
|
|
CNS 11160
2017 Edition Octave and Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及１／３八音度頻帶分析器 |
|
|
|
CNS 517
2017 Edition Metric Buttress Screw Thread, Allowance and Tolerance 公制鋸齒形螺紋（裕度及公差） |
|
|
|
CNS 665
2017 Edition Format for Report of Water Pump Test 水泵檢驗報告書格式 |
|
|
|
CNS 15481-4
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electroniC Equipment - Part 4: Climatic loads 道路車輛－電機電子配備環境條件與試驗－第４部：氣候負載 |
|
|
|
CNS 100
2017 Edition Accuracy Inspection of Table Type Horizontal Boring Machines 床台型臥式搪床精度檢驗 |
Translated |
| Find out:15848Items | To Page of: First -Previous-Next -Last | [339] [340] [341] [342] [343] [344] [345] |
