"C " CNS Standards List |
|
CNS 13982-3
2017 Edition Methods of test for bulk down and feather − Part 3: Composition (content analysis) 羽絨羽毛試驗法-第3部:組成 |
![]() |
|
|
CNS 1131
2017 Edition Pliables plastiC conduits (replaced by CNS 12152) 夾鉗與剪鉗-拔釘鉗 |
![]() |
|
|
CNS 7149
2017 Edition Steel Castings for Low Temperature and High Pressure Service 低溫高壓用鑄鋼件 |
![]() |
|
|
CNS 13127
2017 Edition MetalliC and Other Non -organic Coatings -General Rules for Stationary Outdoor Exposure Corrosion Tests 金屬和無機被覆–靜態戶外曝露腐蝕試驗通則 |
![]() |
|
|
CNS 6135-11
2017 Edition Hearing aids-Part11: Symbols and other marking on hearing aids and related equipment 助聽器-第11部:助聽器及相關設備之符號及標示 |
![]() |
|
|
CNS 3371
2017 Edition Hand Taps for MetriC Coarse Thread, Class 3 公制粗牙手力螺絲攻,精度3級 |
![]() Translated |
|
|
CNS 5967
2017 Edition Bronze SCrewed Swing Check Valves (10kgf/c㎡) 青銅螺紋口擺動型止回閥(10 kgf/㎠) |
![]() |
|
|
CNS 3326
2017 Edition Safety Code of High Pressure for Freeging Devices 冷凍設備高壓安全規章 |
![]() |
|
|
CNS 13144
2017 Edition Method of Test for Internal Bonding Strength of Paper and Paperboard ( Using Tensile Strength Tester ) 紙及紙板內部結合強度試驗法(使用抗張強度試驗機) |
![]() Translated |
|
|
CNS 8474
2017 Edition PunChed Tape Variable Block Format for Positioning and Straight - Cut Numerically Controlled Machine Tools 衝頭(對孔用) |
![]() |
|
|
CNS 7178
2017 Edition ProteCtive gloves for occupational health 熔接用防護手套 |
![]() |
|
|
CNS 4409
2017 Edition SCrew and Washer Assemblies 套有墊圈之螺釘 |
![]() |
|
|
CNS 13331
2017 Edition Sound Calibrator 音壓校正器 |
![]() |
|
|
CNS 3183
2017 Edition Method of test for residues in liquefied petroleum gases 液化石油氣殘餘物試驗法 |
![]() |
|
|
CNS 258
2017 Edition Ring Gauge for Reamer 鉸刀校驗樣圈 |
![]() |
|
|
CNS 12864
2017 Edition Information and doCumentation - International standard book number (ISBN) 國際標準書號 |
![]() |
|
|
CNS 6661
2017 Edition Colors for Color Identification and Coding 色碼用之標準顏色 |
![]() |
|
|
CNS 4655
2017 Edition Hexagon Set SCrews with Half Dog Point and Cone End 六角頭短柱錐形端固定螺釘 |
![]() |
|
|
CNS 10728
2017 Edition Staplers 釘書機 |
![]() |
|
|
CNS 11829
2017 Edition Light Emitting Diodes (for IndiCation) 發光二極體(指示用) |
![]() |
|
|
CNS 4646
2017 Edition Square Taper Washers for High Prestressed I-SeCtions 斜墊圈(工字鐵高強度結構用) |
![]() |
|
|
CNS 228
2017 Edition 60° Center Drills,Straight Form with Conical Protective Chamfer 中心鑽(60°,去角直線錐形) |
![]() Translated |
|
|
CNS 4584
2017 Edition Bolted Connrctions with Reduced Body; Thread Holes for Studs 減徑柄螺栓之結合法–螺樁之旋入螺孔 |
![]() |
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio reCeivers for various classes of emission-Part1:General considerations and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
![]() |
|
|
CNS 11898
2017 Edition Reliability Assured PlastiC Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器(特性M) |
![]() |
|
|
CNS 15832-2-2
2017 Edition Method of test for Coating components − Part 2-2: Component analysis in solvent soluble matter − Softening point (Ring-and-ball method) 塗料成分試驗法-第2-2部:溶劑可溶物中成分分析-軟化點(環與球法) |
![]() |
|
|
CNS 4363
2017 Edition Slotted Countersunk (Flat) Head Screws for Fine Mechanics M 0.4 to M 1.4 精密用有槽平頂埋頭螺釘(標稱直徑自0.4mm至1.4mm) |
![]() |
|
|
CNS 12507
2017 Edition Measuring Methods for Liquid Crystal Display Panel 液晶顯示板測量法 |
![]() |
|
|
CNS 5668
2017 Edition Draw - in Bolt End for Milling MaChine Arbors 銑刀心軸螺栓端部 |
![]() |
|
|
CNS 12720
2017 Edition Method of Test for Polyethylene Shading Net for AgriCulture Use 農業用聚乙烯遮光網檢驗法 |
![]() Translated |
Find out:16181Items | To Page of: First -Previous-Next -Last | [339] [340] [341] [342] [343] [344] [345] |