"U " CNS Standards List |
|
CNS 12295
1988 Edition General RUles for Reliability Assured Power Type Fixed Wire Wound Resistors 可靠度保證功率型線繞固定電阻器總則 |
|
|
|
CNS 12296
1988 Edition Reliability AssUred Power Type Fixed Wire Wound Resistors (S) (Established Failure Rate) 可靠度保證功率型線繞固定電阻器（特性Ｓ）（故障率設定） |
Translated |
|
|
CNS 12258
1988 Edition Method of Electrochemical Reactivation Ratio MeasUrement for Stainless Steels 不銹鋼電化學再活性化率測定法 |
|
|
|
CNS 6158
1988 Edition Method of Test for Electromechanical Switches(Sand and DUst) 電機開關檢驗法－沙及灰塵 |
|
|
|
CNS 12297
1988 Edition Method of Test for Low FreqUency (Below 3 MHz) Electrical Connectors (TP-15 Contact Strength) 頻率3 MHz以下電連接器檢驗法（接點強度TP-15） |
|
|
|
CNS 12256
1988 Edition Ovens for QUartz Crystal Units 石英振盪晶體用恆溫箱 |
|
|
|
CNS 3606
1988 Edition Face Milling CUtters 面銑刀 |
Translated |
|
|
CNS 4366
1987 Edition Hexagon Bolts with Large Widths Across Flats for Steel StrUctures (Joints with Hightensile, Prestressed Bolts) 六角頭螺栓（具大對面寬度、高預力連接鋼結構用） |
|
|
|
CNS 6097
1987 Edition Underfloor Ducts(Steel) 鋼製地板電線槽 |
|
|
|
CNS 5991
1987 Edition RoUnd Punches for Press Dies 衝模用圓衝頭 |
|
|
|
CNS 5992
1987 Edition KnockoUt Equipment for Press Dies 衝模用頂出裝置 |
|
|
|
CNS 5988
1987 Edition StUd Shanks for Press Dies 衝模用栓柄 |
|
|
|
CNS 11941
1987 Edition General RUle for Electronic Scale with Price Indication 計價電子秤總則 |
Translated |
|
|
CNS 12106
1987 Edition Method of Test for Water Absorbency of BibUlous Paper -- Absorption Rate Method 高吸水性紙吸水性試驗法－吸水速率法 |
Translated |
|
|
CNS 12087
1987 Edition Method of Test for Fiber Optic Devices (FOPT-82 FlUid Penetration Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（充膠光纜流體滲透試驗FOTP-82） |
|
|
|
CNS 12086
1987 Edition Method of Test for Fiber Optic Devices (FOPT-55 Method for MeasUring the Coating Geometry of Optical Fibers) 光纖裝置檢驗法（光纖鍍層幾何形狀之測量法FOTP-55） |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler LaUnch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 12082
1987 Edition Method of Test for Fiber Optic Devices (FOPT-30 FreqUency Domain Measurement of Multimode Optical Fiber Information Transmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量FOTP-30） |
|
|
|
CNS 12081
1987 Edition Method of Test for Fiber Optic Devices (FOPT-13 VisUal and Mechanical Inspection of Fibers,Cables,Connectors and Other Fiber Optic Devices) 光纖裝置檢驗法（光纖、光纜、連接器及其他光纖裝置之目視及機械檢查FOTP-13） |
|
|
|
CNS 12080
1987 Edition Glossary of Terms Used in Electronic Measuring Apparatus 電子測定器詞彙 |
|
|
|
CNS 12077
1987 Edition MinimUm Rounded Radii and Drafts of Hot Forging Closed Die 熱鍛閉合模之最小圓角半徑與拔模斜度(角度) |
|
|
|
CNS 12070
1987 Edition Ejectorplate GUide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 12068
1987 Edition SUpport of Die Casting Molds 壓鑄模用支座 |
|
|
|
CNS 11900
1987 Edition Fixed Ceramic Capacitors for Electronic EqUipment (Semiconductor) 電子設備用陶瓷固定電容器（半導體） |
Translated |
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-LaUnch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 3070
1987 Edition InsUlating Oil (for Cold Area) 絕緣油（寒地用） |
Translated |
|
|
CNS 9234
1987 Edition Method of Test for Dry Reed Switches (Standard Test Coils, Single InsUlation 130 ℃ Wire) 乾式簧開關檢驗法（130℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 11939
1987 Edition Setting PlUgs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11938
1987 Edition SprUe Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 11937
1987 Edition RUnner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
| Find out:11052Items | To Page of: First -Previous-Next -Last | [340] [341] [342] [343] [344] [345] [346] |
