"U " CNS Standards List |
|
CNS 10875
1987 Edition Method of Test for Fiber Optic Devices ( FOTP-4 TemperatUre Life Test ) 光纖裝置檢驗法（溫度壽命試驗FOTP-4） |
|
|
|
CNS 5991
1987 Edition RoUnd Punches for Press Dies 衝模用圓衝頭 |
|
|
|
CNS 8223
1987 Edition Method of Test for Low FreqUency (Below 3 MHz) Electrical Connector (TP - 41 Circular Jacket Cable Flexing Test) 頻率3 MHz以下電連接器檢驗法（圓形護套電纜可撓性試驗TP-41） |
|
|
|
CNS 8759
1987 Edition Method of Test for BUlk Specific Gravity of Compacted Bituminous Mixtures Using Saturated Surface-Dry Specimens 瀝青混合料壓實試體容積比重及密度試驗法（飽和面乾法） |
|
|
|
CNS 8757
1987 Edition Method of Test for BUlk Specific Gravity and Density of Compacted Bituminous Mixtyres Using Paraffin- Coated Specimens 瀝青混合料壓實試體容積比重及密度試檢驗法（封臘法） |
|
|
|
CNS 8672
1987 Edition Method of Test for Dry Reed Switches(Carry CUrrent) 乾式簧開關檢驗法（負載電流） |
|
|
|
CNS 8667
1987 Edition Method of Test for Dry Reed Switches(Internal MoistUre) 乾式簧開關檢驗法（內部潮濕） |
|
|
|
CNS 4376
1987 Edition Bow NUts 弓形螺帽 |
|
|
|
CNS 4375
1987 Edition BUtterfly Nuts 蝶形螺帽 |
|
|
|
CNS 4374
1987 Edition Wing NUts ( Small Type ) 翼形螺帽（低型） |
|
|
|
CNS 9097
1987 Edition Thermostats ( PressUre Type ) 恆溫器（壓力式） |
|
|
|
CNS 11935
1987 Edition SUpporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11892
1987 Edition Shears for Flower and Grass CUtting 手剪（修剪花草用） |
|
|
|
CNS 11999
1987 Edition StrUctural Steels with Specified Hardenability Bands 保證硬化能構造用鋼料（Ｈ鋼） |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (QUality Control and Quality Assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-LaUnch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 11830
1987 Edition MeasUring Methods for Light Emitting Diodes (for Indication) 發光二極體(指示用)測量法 |
|
|
|
CNS 11939
1987 Edition Setting PlUgs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 12070
1987 Edition Ejectorplate GUide Pin of Die Casting Molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 11937
1987 Edition RUnner Pull Pins of Molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 12077
1987 Edition MinimUm Rounded Radii and Drafts of Hot Forging Closed Die 熱鍛閉合模之最小圓角半徑與拔模斜度(角度) |
|
|
|
CNS 11933
1987 Edition Ejector GUide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special PUrpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11904
1987 Edition Method of Test for Fiber Optic Devices (FOTP-81 CompoUnd Flow (Drip) Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（有填充物光纜之化合物滴漏試驗FOTP-81） |
|
|
|
CNS 11902
1987 Edition Method of Test for Fiber Optic Devices (FOTP-52 TemperatUre Dependence of Attenuation for Optical Fibers) 光纖裝置檢驗法（溫度變化對光纖衰減之影響FOTP-52） |
|
|
|
CNS 11900
1987 Edition Fixed Ceramic Capacitors for Electronic EqUipment (Semiconductor) 電子設備用陶瓷固定電容器（半導體） |
Translated |
|
|
CNS 11895
1987 Edition General RUles for Reliability Assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 11938
1987 Edition SprUe Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 12106
1987 Edition Method of Test for Water Absorbency of BibUlous Paper -- Absorption Rate Method 高吸水性紙吸水性試驗法－吸水速率法 |
Translated |
|
|
CNS 12154
1987 Edition Uninterruptible Power Supply System (UPS) 不中斷電源供應裝置 |
Translated |
| Find out:11052Items | To Page of: First -Previous-Next -Last | [342] [343] [344] [345] [346] [347] [348] |
