"or " CNS Standards List |
|
CNS 11352
1985 Edition Method of Comparison for Surface Colour 表面色之比較方法 |
|
|
|
CNS 11353
1985 Edition Methods of Measurement for Light Source Colour 光源色之測定方法 |
|
|
|
CNS 11376
1985 Edition Liquid Penetrant Test for Forgings 鍛件液滲檢驗法 |
|
|
|
CNS 5500
1985 Edition Badial Self-aligning Ball Bearings, Parallel and Tapered Bore 自動對位滾珠軸承（平行孔與推拔孔） |
|
|
|
CNS 11377
1985 Edition Magnetic Particle Test for Castings and Forgings 鑄件及鍛件磁粒檢驗法 |
Translated |
|
|
CNS 4328
1985 Edition Electrolytic Capacitors for Motor Starting 電動機起動用電解電容器 |
|
|
|
CNS 4301
1985 Edition Test Code for Accuracy of Surface Grinding Machines with Vertical Grinding Wheel Spindle and Rotary Table 旋轉床台型立式平面磨床精度檢驗標準 |
|
|
|
CNS 6554
1985 Edition General Rules for Enameled Copper Wires 漆包銅線總則 |
Translated |
|
|
CNS 4300
1985 Edition Test Code for Accuracy of Surface Grinding Machines With Horizontal Grinding Wheel Spindle and Reciprocating Table 往復床台型臥式平面磨床精度檢驗標準 |
Translated |
|
|
CNS 3411
1985 Edition Sickles for Paddy Harvest 割禾鐮刀 |
Translated |
|
|
CNS 3563
1985 Edition Method of Test for Low Elongation Stress of Vulcanized Rubber 硫化橡膠低伸長應力試驗法 |
|
|
|
CNS 11273
1985 Edition Method of Test for Fineness of Hydraulic Cement by the Test Sieve 0.045 mm CNS 386 水硬性水泥以試驗篩０．０４５ｍｍＣＮＳ３８６濕篩試驗法 |
|
|
|
CNS 10899
1984 Edition Method of Test for Flat Quick-Connect Terminals 平板型接頭檢驗法 |
|
|
|
CNS 5026
1984 Edition Welding Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 1419
1984 Edition Method of Test for Acetone 丙酮檢驗法 |
|
|
|
CNS 5022
1984 Edition Thyristorstack for Welding Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 11160
1984 Edition Octave and Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及1/3八音度頻帶分析器 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 2900
1984 Edition Polyvinyl Chloride Insulated Copper Wire 聚氯乙烯絕緣屋內電話線 |
Translated |
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and Sheated Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5298
1984 Edition Hose Clamps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
| Find out:10886Items | To Page of: First -Previous-Next -Last | [342] [343] [344] [345] [346] [347] [348] |
