"or " CNS Standards List| Rubber products | Insulation coordination | Plug Gauge | Method determining | Knurled Nuts | Rubber, vulcanized | Standard test | Method test | |
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 11160
1984 Edition Octave and Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及1/3八音度頻帶分析器 |
|
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 10006
1984 Edition Method for Photoelectric Emission Spectrochemical Analysis of Iron And Steel 鐵及鋼之光電式發光光譜分析法 |
|
|
|
CNS 10502
1984 Edition Method for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 10761
1984 Edition Method of Test for Surface Wax on Waxed Paper or Paperboard 蠟紙及蠟紙板之表面蠟量試驗法 |
Translated |
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 10735
1984 Edition Plastic Rims for Bicycles 平車或跑車型自行車塑膠輪圈 |
|
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and Sheated Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 168
1983 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 4607
1983 Edition Studs for T-Nuts 螺樁（Ｔ形螺帽用） |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 4608
1983 Edition Studs for Welding 螺樁（熔接用） |
|
|
|
CNS 4107
1983 Edition Flat Seal for Hydraulic Couplings 液壓接頭用扁封 |
|
|
|
CNS 170
1983 Edition Flat Fitting Keys (for Thin Hub) 配合平鍵（用於薄轂） |
|
|
|
CNS 4262
1983 Edition Method of Life Test for Single Point Carbide Tools 碳化物車刀性能試驗方法 |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys and Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 4647
1983 Edition Square Taper Washers for High Prestressed Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 4584
1983 Edition Bolted Connrctions with Reduced Body; Thread Holes for Studs 減徑柄螺栓之結合法－螺樁之旋入螺孔 |
|
|
|
CNS 3155
1983 Edition Chisels for Stone Work 石工鑿 |
|
| Find out:10886Items | To Page of: First -Previous-Next -Last | [344] [345] [346] [347] [348] [349] [350] |
