"or " CNS Standards List |
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 10734
1984 Edition Method of Test for the Plastic Rims of Bicycle 平車或跑車型自行車塑膠輪圈檢驗法 |
|
|
|
CNS 6415
1984 Edition Series of modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 2900
1984 Edition Polyvinyl Chloride Insulated Copper Wire 聚氯乙烯絕緣屋內電話線 |
Translated |
|
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis for Pig Iron and Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 5280
1984 Edition Helix Angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 4262
1983 Edition Method of Life Test for Single Point Carbide Tools 碳化物車刀性能試驗方法 |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys and Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 3155
1983 Edition Chisels for Stone Work 石工鑿 |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 170
1983 Edition Flat Fitting Keys (for Thin Hub) 配合平鍵（用於薄轂） |
|
|
|
CNS 168
1983 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 4107
1983 Edition Flat Seal for Hydraulic Couplings 液壓接頭用扁封 |
|
|
|
CNS 4584
1983 Edition Bolted Connrctions with Reduced Body; Thread Holes for Studs 減徑柄螺栓之結合法－螺樁之旋入螺孔 |
|
|
|
CNS 4607
1983 Edition Studs for T-Nuts 螺樁（Ｔ形螺帽用） |
|
|
|
CNS 4608
1983 Edition Studs for Welding 螺樁（熔接用） |
|
|
|
CNS 4646
1983 Edition Square Taper Washers for High Prestressed I-Sections 斜墊圈（工字鐵高強度結構用） |
|
| Find out:10886Items | To Page of: First -Previous-Next -Last | [344] [345] [346] [347] [348] [349] [350] |
