"part " CNS Standards List| Method test | Method Test | Steel Castings | Spilt Pins | Industrial heptanes | Method test | Method Test | Furniture － | |
|
CNS 60245-2
2019 Edition Rubber insulated cables − Rated voltages up to and including 450/750 V − part 2: Test methods 額定電壓450/750 V以下橡膠絕緣電纜－第2部：試驗法 |
|
|
|
CNS 15125-2
2019 Edition Solar heating - Domestic water heating systems - part 2 : Outdoor test methods for system performance characterization and yearly performance prediction of solar-only systems 太陽能加熱－家用熱水系統－第２部：僅用太陽能系統的性能特性與年度性能預測之室外試驗法 |
|
|
|
CNS 15764-5
2019 Edition Footwear − Test methods for insoles – part 5: Abrasion resistance of insoles 鞋類－中底板試驗法－第5 部：中底板之耐摩損性 |
|
|
|
CNS 15763-4
2019 Edition Footwear − Test methods for outsoles – part 4: Tensile strength and elongation of outsoles 鞋類－外底試驗法－第4 部：外底之抗拉強度及伸長率 |
|
|
|
CNS 15077-6
2019 Edition Test conditions for machining centers - part 6 : Accuracy of feeds, speeds and interpolations 切削中心機之檢驗條件－第６部：進給、速率與插值之精度 |
|
|
|
CNS 15130-2-2
2019 Edition Tests on electric and optical fibre cables under fire conditions − part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame 電纜及光纜之燃燒試驗－ 第2-2部:單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 擴散火焰之程序 |
|
|
|
CNS 15077-3
2019 Edition Test conditions for machining centres - part 3 : Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis) 切削中心機之檢驗條件－第３部：具整合型分段指示或連續萬向分度頭之機器幾何檢驗（垂直Ｚ軸） |
|
|
|
CNS 15228-4
2019 Edition Test methods for lead-free solders - part 4: Solderbility test by a wetting balance method 無鉛銲錫試驗法－第４部：沾錫性試驗－潤濕平衡法 |
|
|
|
CNS 15763-9
2019 Edition Footwear − Test methods for outsoles – part 9: Compression energy of outsoles 鞋類－外底試驗法－第9 部：外底之壓縮能 |
|
|
|
CNS 14545-5
2019 Edition Fire hazard testing-part 2:Test methods-Section 1/sheet 1:Glow-wire end-product test and guidance 火災危險性試驗－第２部：試驗方法－第１章／第１單元：完成品之熾熱線試驗及指引 |
|
|
|
CNS 15207-2
2019 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - part 2: Absorber-lined shielded enclosure 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第２部：內襯吸波材料屏蔽圍體 |
|
|
|
CNS 15762-3
2019 Edition Footwear − Test methods for uppers − part 3: Colour fastness to rubbing of uppers, linings and insocks 鞋類－鞋面試驗法－第3 部：鞋面、內裡及鞋墊之摩擦色牢度 |
|
|
|
CNS 15187-3
2019 Edition Low-voltage fuses - part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications) 低壓熔線－第３部︰非專業人員用熔線之補充規定（以家用及類似用途為主之熔線） |
|
|
|
CNS 16108-2
2019 Edition Railway applications − Fire protection on railway vehicles − part 2: Requirements for fire behaviour of materials and components 鐵路應用－鐵路車輛防火－第2部：材料及零組件火災時之行為要求 |
|
|
|
CNS 15785-4
2019 Edition Tool holders with cylindrical shank − part 4: Type C with rectangular axial seat 具圓柱柄之刀具夾持器－第4 部：具長方形軸向座之C 型 |
|
|
|
CNS 15094-2
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - part 2: Removal of acetaldehyde 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第2部：乙醛去除性能 |
|
|
|
CNS 15094-1
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - part 1: Removal of nitric oxide 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第1部：氮氧化物去除性能 |
|
|
|
CNS 16093-3
2019 Edition Welding and allied processes − Types of joint preparation − part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys 銲接及其相關製程－接頭準備型式－第3部：鋁及鋁合金的惰氣遮護金屬電弧銲接及惰氣遮護鎢極電弧銲接 |
|
|
|
CNS 15207-3
2019 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - part 3: Transverse electromagnetic (TEM) cell 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第３部：橫向電磁波室 |
|
|
|
CNS 15764-3
2019 Edition Footwear − Test methods for insoles – part 3: Water absorption and desorption of insoles and insocks 鞋類－中底板試驗法－第3 部：中底板及鞋墊之吸水量及脫水率 |
|
|
|
CNS 15781-2
2019 Edition Measurement of smoke density of cables burning under defined conditions − part 2: Test procedure and requirements 電(光)纜於特定條件下燃燒之煙密度量測－第2 部：試驗程序及要求 |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 62282-4-101
2019 Edition Fuel cell technologies − part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) − Safety of electrically powered industrial trucks 燃料電池技術－第4-101部：作為道路車輛及輔助電力單元之外的推進用燃料電池發電系統－電驅動產業搬運車之安全性 |
|
|
|
CNS 15755-4-2
2019 Edition Conversion tables for units − part 4-2: Volume − Cubic centimeter and cubic inch 單位換算表－第4-2 部：體積－立方公分與立方英寸 |
|
|
|
CNS 15748-1
2019 Edition Integrated circuits − Measurement of electromagnetic emissions, 150 kHz to 1 GHz − part 1: General conditions and definitions 積體電路－150 kHz 至1 GHz 電磁放射量測－第1 部：一般條件及定義 |
|
|
|
CNS 9359-5
2019 Edition Information technology − Vocabulary − part 5: Representation of data 資訊技術－詞彙－第5 部：資料表示法 |
|
|
|
CNS 15762-2
2019 Edition Footwear − Test methods for uppers − part 2: Flex resistance of uppers and linings 鞋類－鞋面試驗法－第2 部：鞋面及內裡之耐曲折性 |
|
|
|
CNS 16118-1
2019 Edition Qualification testing of welders for underwater welding − part 1: Hyperbaric wet welding 水下銲接技術員檢定試驗－第1部：高壓濕式銲接 |
|
|
|
CNS 15228-6
2019 Edition Test methods for lead-free solders - part 6: 45° pull test of leadframe type package 無鉛銲錫試驗法－第６部：釘架引腳式封裝結構之銲錫接腳４５°拉力試驗法 |
|
|
|
CNS 15785-3
2019 Edition Tool holders with cylindrical shank − part 3: Type B with rectangular radial seat 具圓柱柄之刀具夾持器－第3 部：具長方形徑向座之B 型 |
|
| Find out:2535Items | To Page of: First -Previous-Next -Last | [30] [31] [32] [33] [34] [35] [36] |
