"N,N " CNS Standards List |
|
CNS 10001
2017 Edition Seamless Nickel-Chromium-Iron Alloy Tubes for Heat Exchanger 熱交換器用無縫鎳鉻鐵合金管 |
|
|
|
CNS 2057
2017 Edition Power Thrasher 耕耘機〔動力15仟瓦（20馬力）以下〕 |
|
|
|
CNS 7748
2017 Edition Method of Test for Viscosity of Pulp ( Cannon -Fenske Capillary Viscometer Method ) 紙漿黏度試驗法（Ｃａｎｎｏｎ–Ｆｅｎｓｋｅ毛細管黏度計法） |
Translated |
|
|
CNS 15552
2017 Edition Packaging - Accessible design - General requirements 包裝－無障礙設計 - 一般要求 |
|
|
|
CNS 2534
2017 Edition Method of Test for Natural Rubber Latex 天然橡膠乳液檢驗法 |
Translated |
|
|
CNS 5154
2017 Edition Photography-Processing chemicals-Specifications for glacial acetic acid 照相術─顯像處理化學品─冰醋酸規格 |
|
|
|
CNS 13579
2017 Edition Fire Hydrant Valves 消防栓閥 |
|
|
|
CNS 15545
2017 Edition Instant coffee - Determination of free-flow and compacted bulk densities 即溶咖啡－自由流動與緊密 堆積總體積密度測定法 |
|
|
|
CNS 13941
2017 Edition Micrographics-Microfilming of documents on 16mm and 35mm silver-gelatin type microfilm-Operating procedures 微縮技術–１６ｍｍ及３５ｍｍ銀鹽片之文件縮攝法–作業程序 |
|
|
|
CNS 9113
2017 Edition Symbols of Fire Alarm System of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖火警警報系統類符號 |
|
|
|
CNS 15964
2017 Edition Information technology − Automatic identification and data capture techniques − QR Code bar code symbology 資訊技術－自動識別及資料擷取技術－QR 碼條碼符號表示法 |
|
|
|
CNS 13352-3
2017 Edition Micrographics – Vocabulary – Part 3: Film processing 微縮技術－詞彙－第3部：軟片處理法 |
|
|
|
CNS 209
2017 Edition Long Drills with Square Taper Shank 方錐柄長鑽頭 |
Translated |
|
|
CNS 6151
2017 Edition Method of Test for Electromechanical Switches(Overload) 電機開關檢驗法–過負荷 |
|
|
|
CNS 15996
2017 Edition Plastic fuel tanks for passenger cars (replaced by CNS 14579-1) 燃氣用塑膠軟管 |
|
|
|
CNS 4762
2017 Edition Method of 5 Percent Sulfuric Acid Test for Stainless Steels 不銹鋼之５％硫酸腐蝕試驗法 |
|
|
|
CNS 7143
2017 Edition Steel Castings for Welded Structure 銲接結構用鑄鋼件 |
|
|
|
CNS 13781
2017 Edition Endurance Testing Methods for Infrared Emitting Diodes (for Automation)-Burn-In Test (Forward Bias) 自動控制用紅外發光二極體耐久性試驗法–預燒試驗（順向偏壓） |
|
|
|
CNS 11646
2017 Edition Glassfiber reinforced plastic pipe for sewer and industrial use 污水與工業用玻璃纖維強化塑膠管 |
|
|
|
CNS 11572
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-46 Continuity Test) 頻率３ＭＨｚ以下電連接器檢驗法（連續性試驗ＴＰ–４６） |
|
|
|
CNS 13622
2017 Edition Fixed chip resistor for use in electronic equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 13331
2017 Edition Sound Calibrator 音壓校正器 |
|
|
|
CNS 15985-5
2017 Edition Qualification testing of welders − Fusion welding − Part 5: Titanium and titanium alloys, zirconium and zirconium alloys 銲工檢定試驗－熔融銲接－第5部：鈦及鈦合金、鋯及鋯合金 |
|
|
|
CNS 14630
2017 Edition Structural coniferous sawn lumber 針葉樹結構用製材 |
|
|
|
CNS 12865-9
2017 Edition Method of Test for Digital Microelectronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 13545
2017 Edition Acoustics - Preferred Frequencies for Measurements 聲學量測上優選的頻率 |
|
|
|
CNS 12289
2017 Edition Reliability Assured Fixed Metal Film Resistors (H,J,K) (Established Failure Rate) 可靠度保證金屬皮膜固定電阻器（特性Ｈ，Ｊ及Ｋ）（故障率設定） |
Translated |
|
|
CNS 14232-2
2017 Edition Health Level Seven (HL7) - Part 2: Control 健康資訊交換第七層協定－第２部：控制 |
|
|
|
CNS 9097
2017 Edition Thermostats ( Pressure Type ) 恆溫器（壓力式） |
|
|
|
CNS 3314
2017 Edition Canned bean sprout 豆芽菜罐頭 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [348] [349] [350] [351] [352] [353] [354] |
