"E " CNS Standards List| Low voltage | Office Machine | Multiple Ratio | Method test | Road vehicles | Throat Plates | Safety | Steel Method | |
|
CNS 14301-3
2017 Edition Optical fibEr cables Part 3: telecommunication cables - specifications 光纜－第三部分:電信光纜規格 |
|
|
|
CNS 12496
2017 Edition Laboratory BEating of Pulp (PFI Mill Method) 實驗室紙漿叩解法（ＰＦＩ研磨機法） |
Translated |
|
|
CNS 11625
2017 Edition PapEr Dielectric Capacitors for AC and DC By-Pass Radio-Interference Reduction 交直流分路射頻干擾衰減用紙介質電容器 |
|
|
|
CNS 739
2017 Edition MEthod of Test for Rubber Inner Tubes for Bicycles 自行車用橡膠內胎檢驗法 |
|
|
|
CNS 9108
2017 Edition Symbols of Distribution of IntErior Wiring Diagram for Architectural Plans 屋內配線設計圖配電箱類符號 |
|
|
|
CNS 14866-1
2017 Edition MEasurement of water flow in fully charged closed conduits − Meters for cold potable water and hot water − Part 1: Specifications 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第1部：規範 |
|
|
|
CNS 10323
2017 Edition Low-voltagE three-phasesquirrel-cage induction motors(for special frame) 低壓三相鼠籠型感應電動機(特殊框號用) |
|
|
|
CNS 12292
2017 Edition REliability Assured Fixed Carbon Composition Resistors (Established Failure Rate) 可靠度保證混合碳固定電阻器（故障率設定） |
Translated |
|
|
CNS 10926
2017 Edition MEthod of Test for Fiber Optic Devices (FOTP-27 Measuring Outside (Uncoated) Diameter of Optical Fibers) 光纖裝置檢驗法（無外被光纖外徑測量法ＦＯＴＰ–２７） |
|
|
|
CNS 769
2017 Edition MEthod of Test for Boiled Linseed Oil 熟煉亞麻仁油檢驗法 |
Translated |
|
|
CNS 15421
2017 Edition OfficE furniture - Chairs 辦公室用椅 |
|
|
|
CNS 7524
2017 Edition Edible whey powder 食用乳清粉 |
Translated |
|
|
CNS 4696
2017 Edition Round HEad Nip Bolts 圓頭單鰭螺栓 |
|
|
|
CNS 13335
2017 Edition MEthod of Test for Dart Impact Resistance of Plastic Films and Sheets 塑膠薄膜及薄片落鏢衝擊試驗法 |
|
|
|
CNS 11057
2017 Edition Glossary of TErms Used in Automatic Control (General) 自動控制一般詞彙 |
|
|
|
CNS 218
2017 Edition CountEr-boring Drill with Morse Taper Shank （莫氏）推拔柄柱坑鑽頭 |
Translated |
|
|
CNS 13514
2017 Edition REady - Mixed Mortar for Unit Masonry 磚、石墁砌用預拌墁料 |
|
|
|
CNS 3413
2017 Edition AssEmbly tools for screws and nuts - Double-headed,flat and offset,box wrenches,test torque series B 螺釘及螺帽之裝配工具–雙頭梅花扳手（Ｂ級扭矩） |
Translated |
|
|
CNS 13545
2017 Edition Acoustics - PrEferred Frequencies for Measurements 聲學量測上優選的頻率 |
|
|
|
CNS 5664
2017 Edition TEst Code for Accuracy of Four-side Planers and Moulders 自動四面刨床精度檢驗標準 |
|
|
|
CNS 6415
2017 Edition SEries of modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 13982-4
2017 Edition MEthods of test for bulk down and feather − Part 4: Determination of the oil and fat content 羽絨羽毛試驗法－第4部：油脂含量測定法 |
|
|
|
CNS 12587
2017 Edition TEchnical Terms for Analytical Chemistry (Electrochemistry Division) 分析化學用語（電化學部門） |
|
|
|
CNS 3633
2017 Edition Basic Environmental Testing Procedures Part 2: Tests, Test N: Change of Temperature 環境試驗法（電氣、電子）–溫度變化試驗 |
|
|
|
CNS 11295
2017 Edition SpEcification of Colours According to their Their Attributes 利用三屬性表示色彩之方法 |
|
|
|
CNS 522
2017 Edition Snap GaugE for Whitworth Thread (Manufacturing Tolerance and Wear Limit) 韋氏螺紋量規（製造公差及損磨限） |
|
|
|
CNS 12558
2017 Edition MEthod of Test for Solar Water Heater System (Automatic Cycle) 自然循環式太陽能熱水系統檢驗法 |
|
|
|
CNS 11655
2017 Edition MEthod of Test for Glassfiber Reinforced Plastic Water Tank 玻璃纖維強化塑膠儲水槽檢驗法 |
|
|
|
CNS 5995
2017 Edition MastEr Dies for Die Casting Metal Mold 壓鑄模用主模板 |
|
|
|
CNS 13061
2017 Edition High TEnsile Strength Steels for Tower Structural Purposes 鐵塔用高強度鋼料 |
|
| Find out:15848Items | To Page of: First -Previous-Next -Last | [353] [354] [355] [356] [357] [358] [359] |
