"H " CNS Standards List |
|
CNS 11306
1985 Edition MetHods of Determination for Zirconium in Steel 鋼中鋯定量法 |
|
|
|
CNS 11328
1985 Edition Sets of High Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件 |
|
|
|
CNS 11399
1985 Edition MetHod of Straight-Beam Ultrasonic Test for Steel Plate for Pressure Vessel Use 壓力容器用鋼板直束法超音波檢驗法 |
|
|
|
CNS 11448
1985 Edition MetHods of Determination for Tellurium in Steel 鋼中碲定量法 |
|
|
|
CNS 11290
1985 Edition MetHod of Test for Starch in Paper 紙中澱粉含量試驗法 |
Translated |
|
|
CNS 5968
1985 Edition Bronze Screwed Lift CHeck Valves (10kgf/c㎡) 青銅螺紋口升降型止回閥(10 kgf/cm2) |
|
|
|
CNS 11287
1985 Edition MetHods for Chemical Analysis of Silica Rock and Sand 矽石及矽砂化學分析法 |
|
|
|
CNS 11291
1985 Edition MetHod of Test for Physical Properties of Handsheet 手抄紙物理性質試驗法 |
Translated |
|
|
CNS 11353
1985 Edition MetHods of Measurement for Light Source Colour 光源色之測定方法 |
|
|
|
CNS 11351
1985 Edition MetHods of Measurement for Colour of Reflecting of Transmitting Objects 物體色之測定方法 |
|
|
|
CNS 11295
1985 Edition Specification of Colours According to tHeir Their Attributes 利用三屬性表示色彩之方法 |
|
|
|
CNS 5501
1985 Edition Self - Aligning Ball Bearings: Wide Inner Race, Inner Race witH Clamping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 11051
1985 Edition General Rules for Ultrasonic Testing by Pulse EcHo Technique 脈波反射式超音波檢驗法通則 |
|
|
|
CNS 11329
1985 Edition Test MetHod for the Sets of High Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件檢驗法 |
|
|
|
CNS 11356
1985 Edition Hand Operated Tube Bender 手動彎管器 |
|
|
|
CNS 5967
1985 Edition Bronze Screwed Swing CHeck Valves (10kgf/c㎡) 青銅螺紋口擺動型止回閥(10 kgf/cm2) |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear TeetH Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5274
1984 Edition Base Tangent LengtHs of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine MecHanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5275
1984 Edition Base Tangent LengtHs of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine MecHanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of SHaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute TootH System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears in tHe 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear TeetH Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5298
1984 Edition Hose Clamps for the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 5280
1984 Edition Helix Angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 4732
1984 Edition Knurled Nuts witH Ring 有環滾紋螺帽 |
|
|
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Pinion Single TootH Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
| Find out:11384Items | To Page of: First -Previous-Next -Last | [353] [354] [355] [356] [357] [358] [359] |
