"C,E " CNS Standards List| Hexagon Domed | Hard Bast | Contact Ratio | Polyester Spun | Reflection Lamps | Audio , | Marine Control | Finishes Tolerances | |
|
CNS 287
2017 Edition Method of Test for Chemical Analysis of Limes 石灰化學分析法 |
|
|
|
CNS 6883
2017 Edition Cast Steel Flanged Angle Valves (10 kgf/㎠) 鑄鋼凸緣型角閥（10 kgf/㎠） |
|
|
|
CNS 5714
2017 Edition Face-to-Face and End-to-End Dimensions of Cocks 旋塞端面間之尺度 |
|
|
|
CNS 15971
2017 Edition Personal protective equipment – Test methods for sunglasses and related eyewear 個人防護設備－太陽眼鏡及相關眼睛配戴物試驗法 |
|
|
|
CNS 16002
2017 Edition Rubber compounding ingredients − Carbon black − Determination of specific surface area by nitrogen adsorption method − Single-point procedures 橡膠配合劑－碳黑－比表面積之氮吸附測定－單點程序 |
|
|
|
CNS 9795
2017 Edition Expansion joint for pressure vessels 壓力容器之伸縮接頭 |
|
|
|
CNS 12256
2017 Edition Ovens for Quartz Crystal Units 石英振盪晶體用恆溫箱 |
|
|
|
CNS 1068
2017 Edition Method of Test for Cork Sheet for Gasket 軟木紙檢驗法 |
|
|
|
CNS 15623
2017 Edition Paragliding equipment – Emergency parachutes – Safety requirements and test methods 飛行傘設備－緊急降落傘－安全要求與試驗法 |
|
|
|
CNS 3608
2017 Edition End Mills with Straight Shank 直柄端銑刀 |
Translated |
|
|
CNS 8227
2017 Edition Method of Test for Dry Reed Switches (Operation Parameters) 乾式簧開關檢驗法（動作參數） |
|
|
|
CNS 14341
2017 Edition Optical spectrum analyzer 光譜分析儀 |
|
|
|
CNS 567
2017 Edition Hot Headed Rivet 熱作鉚釘 |
|
|
|
CNS 665
2017 Edition Format for Report of Water Pump Test 水泵檢驗報告書格式 |
|
|
|
CNS 1190
2017 Edition Half-round File for Carpenter, Thin Sharp End 木工用細尖頭扁圓銼 |
Translated |
|
|
CNS 6147
2017 Edition Method of Test for Electromechanical Switches(Switch Resistance) 電機開關檢驗法–開關電阻值 |
|
|
|
CNS 12106
2017 Edition Method of Test for Water Absorbency of Bibulous Paper -- Absorption Rate Method 高吸水性紙吸水性試驗法–吸水速率法 |
Translated |
|
|
CNS 3445
2017 Edition Method of test for milk and milk products - Determination of lactose content 乳品檢驗法－乳糖之測定 |
|
|
|
CNS 16011-2
2017 Edition Machine tools − Connecting dimensions of spindle noses and work holding chucks − Part 2: Camlock type 工具機－主軸鼻端及工件夾持夾頭之連接尺度－第2部：凸輪鎖型 |
|
|
|
CNS 11572
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-46 Continuity Test) 頻率３ＭＨｚ以下電連接器檢驗法（連續性試驗ＴＰ–４６） |
|
|
|
CNS 1199
2017 Edition Feather-edge File for Smith 鐵工用菱形銼 |
Translated |
|
|
CNS 12361
2017 Edition Method of Test for Fiber Optic Devices ( FOTP-85 Fiber Optic Cable Twist Test) 光纖裝置檢驗法（光纜扭轉試驗ＦＯＴＰ–８５） |
|
|
|
CNS 10874
2017 Edition Method of Test for Fiber Optic Devices ( FOTP-18 Acceleration ) 光纖裝置檢驗法（加速度試驗ＦＯＴＰ–１８） |
|
|
|
CNS 5505
2017 Edition Magneto Ball Bearings 小電器用滾珠軸承 |
|
|
|
CNS 12364
2017 Edition Method of Test for Fiber Optic Devices ( FOTP-98 Fiber Optic Cable External Freezing Test) 光纖裝置檢驗法（光纜外部結冰試驗ＦＯＴＰ–９８） |
|
|
|
CNS 3673
2017 Edition Dimensions of Tires for Industrial Vehicles and Off Road Service 工業車輛及建設工程用輪胎之尺度 |
Translated |
|
|
CNS 15559
2017 Edition Flexible and rigid cellular polymeric materials - Accelerated ageing tests 軟質及硬質發泡材料－加速老化試驗 |
|
|
|
CNS 12403
2017 Edition Sphere Holder and It's Accessories for Liquified Petroleum Gas 液化石油氣球型儲槽及其附屬設備 |
|
|
|
CNS 4377
2017 Edition Square Thin Nuts 方螺帽（低型） |
|
|
|
CNS 4569
2017 Edition T-Head Bolts with One-Rounded Head Ｔ形頭螺栓（具單邊圓角） |
|
| Find out:15848Items | To Page of: First -Previous-Next -Last | [361] [362] [363] [364] [365] [366] [367] |
