"CNS " CNS Standards List |
|
CNS 12403
2017 Edition Sphere Holder and It's Accessories for Liquified Petroleum Gas 液化石油氣球型儲槽及其附屬設備 |
![]() |
|
|
CNS 4247
2017 Edition Flat Knurled Thumb Screws 輥紋扭頭平螺釘 |
![]() |
|
|
CNS 7524
2017 Edition Edible whey powder 食用乳清粉 |
![]() Translated |
|
|
CNS 11993
2017 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法(長距離斜射率光纖光譜衰減測量之光投射條件FOTP–50) |
![]() |
|
|
CNS 6305
2017 Edition Test Code for Accuracy of Feed Carriages of Band Saw Mills 帶鋸機進給溜板精度檢驗標準 |
![]() |
|
|
CNS 2470
2017 Edition Testing Standard for Hanging and Table Clocks (Middle and High Grade) 中級及高級掛鐘及桌鐘檢驗標準 |
![]() |
|
|
CNS 5500
2017 Edition Badial Self-aligning Ball Bearings, Parallel and Tapered Bore 自動對位滾珠軸承(平行孔與推拔孔) |
![]() |
|
|
CNS 12519
2017 Edition Metal Spectacle Frames 金屬眼鏡架 |
![]() |
|
|
CNS 7002
2017 Edition Machine Taper Pin Reamers with Parallel Shanks 推拔銷鉸刀(圓柱柄,機用) |
![]() |
|
|
CNS 12255
2017 Edition Synthetic Quartz Crystal 人工石英原晶 |
![]() |
|
|
CNS 4373
2017 Edition Wing Nuts (Heavy Type) 翼形螺帽(高型) |
![]() |
|
|
CNS 7865
2017 Edition Laminated Springs Spring Link Washers and Intermediate Spring Link Washers for Spring Suspension 彈簧板端鞍板及中間板懸吊彈簧用 |
![]() Translated |
|
|
CNS 11072
2017 Edition Method of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光X射線分析法 |
![]() |
|
|
CNS 223
2017 Edition Podded pea 起鑽鑽頭 |
![]() Translated |
|
|
CNS 11575
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-55 Current Cycling Test) 頻率3MHz以下電連接器檢驗法(電流循環試驗TP–55) |
![]() |
|
|
CNS 11905
2017 Edition Method of Test for Fiber Optic Devices (FOTP-83 Cable to Interconnecting Device Axial Compressive Loading) 光纖裝置檢驗法(光纜至連接器之軸向壓力負載FOTP–83) |
![]() |
|
|
CNS 5521
2017 Edition Polyester Film Lamination for Electrical Insulation 電器用聚酯膜 |
![]() |
|
|
CNS 12457
2017 Edition Method of Test for Corrosion Inhibitor for Reinforsing Steel in Concrete 鋼筋混凝土用防銹劑檢驗法 |
![]() |
|
|
CNS 1188
2017 Edition Flat File for Carpenter, Sharp Flat End 木工用尖平頭扁平銼 |
![]() Translated |
|
|
CNS 5747
2017 Edition Rubber insulated lead wires for electric machinery and apparatus 電機機械及裝置用橡膠絕緣引出線 |
![]() |
|
|
CNS 60227-1
2017 Edition Polyvinyl chloride insulated cables of rated voltages up to and including 450/750V − Part 1: General requirements 額定電壓450/750 V以下聚氯乙烯絕緣電纜-第1 部:一般要求 |
![]() |
|
|
CNS 15876-2
2017 Edition Specification and qualification of welding procedures for metallic materials − Welding procedure tests − Part 2: Arc welding of aluminium and its alloys 金屬材料銲接程序規範書及其檢定-銲接程序試驗-第2部:鋁及鋁合金的電弧銲接 |
![]() |
|
|
CNS 4476
2017 Edition Slotted Set Screws with Cup Point 有槽無頭杯形端固定螺釘 |
![]() |
|
|
CNS 7166
2017 Edition Method of Test for Color After Heating of Fatty Acids 脂肪酸加熱後之顏色檢驗法 |
![]() |
|
|
CNS 4120
2017 Edition Type G standard test block for ultrasonic normal beam testing 超音波檢測用G型標準規塊 |
![]() |
|
|
CNS 4998
2017 Edition Long Shank Machine Taps with Nominal Diameters from 3 to 24 mm 長柄機力螺絲攻(標稱直徑自3mm至24mm) |
![]() Translated |
|
|
CNS 15544-2
2017 Edition Load restraint assemblies on road vehicles - Safety - Part 2: Web lashing made from man-made fibres 道路車輛用負載束縛組合-安全規範-第2部:人造纖維製繫帶綑綁器 |
![]() |
|
|
CNS 11784
2017 Edition Testing Tapes for Magnetic Sound Recording and Reproducing Equipment 錄音機試驗用錄音帶 |
![]() |
|
|
CNS 14492-3
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part3:Receivers for amplitude-modulated sound-broadcasting emissions 不同發射類別之無線電接收機的量測方法-第3部:調幅聲音廣播發射適用的接收機 |
![]() |
|
|
CNS 6218
2017 Edition High Purity Octane 高純度正辛烷 |
![]() |
Find out:16181Items | To Page of: First -Previous-Next -Last | [366] [367] [368] [369] [370] [371] [372] |