"CNS " CNS Standards List |
|
CNS 15326
2017 Edition Information technology - Automatic identification and data capture techniques - Syntax for high-capacity ADC media 資訊技術—自動識別與資料擷取技術—高容量自動資料擷取媒體之語法 |
|
|
|
CNS 4410
2017 Edition Tapping Screw and Washer Assemblies 套有墊圈之自攻螺釘 |
|
|
|
CNS 13622
2017 Edition Fixed chip resistor for use in electronic equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 4434
2017 Edition Round Nuts With Drilled Holes in One Face 頂孔圓螺帽 |
|
|
|
CNS 5274
2017 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 9114
2017 Edition Symbols of Television and Broadcast Equipment of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電視、播音類符號 |
|
|
|
CNS 11112
2017 Edition Methods of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 12449
2017 Edition Method of Test for Spectacle Lenses 眼鏡片檢驗法 |
|
|
|
CNS 12336
2017 Edition Multi-wrenches 萬能扳手 |
|
|
|
CNS 12338
2017 Edition Crowbars 撬桿 |
|
|
|
CNS 13652
2017 Edition Reliability Testing for Light Emitting Diode(for Communication) 通信用發光二極體之可靠度測試 |
|
|
|
CNS 3424
2017 Edition Varnished Cotton Bias Tape 漆斜條棉布帶 |
|
|
|
CNS 9359-7
2017 Edition Information technology - Vocabulary - Part 7: Computer programming 資訊技術－詞彙－第7部：電腦程式設計 |
|
|
|
CNS 9366
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 13 Mating and Unmating Forces) 頻率３ＭＨｚ以下電連接器檢驗法（配對及分離力量ＴＰ–１３） |
|
|
|
CNS 517
2017 Edition Metric Buttress Screw Thread, Allowance and Tolerance 公制鋸齒形螺紋（裕度及公差） |
|
|
|
CNS 541
2017 Edition Shovels with Point End 尖鏟 |
Translated |
|
|
CNS 6135-8
2017 Edition Hearing aids-Part8: Measurement of performance characteristics of hearing aids under simulated in situ working conduction 助聽器－第8部:模擬現場工作情況之性能特性的量測 |
|
|
|
CNS 15552
2017 Edition Packaging - Accessible design - General requirements 包裝－無障礙設計 - 一般要求 |
|
|
|
CNS 5410
2017 Edition Bobbins of Industrial Sewing Machines 工業用縫紉機梭線輪 |
|
|
|
CNS 3510
2017 Edition Copper and copper alloy covered electrodes 銅及銅合金被覆銲條 |
|
|
|
CNS 5266
2017 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 14819
2017 Edition Method of test for surface flammability of materials using a radiant heatenergy source 材料表面耐燃燒性試驗法-輻射熱源垂直試驗法 |
|
|
|
CNS 15329-7
2017 Edition Information technology - Radio frequency identification device conformance test methods - Part 7: Test methods for active air interface communications at 433 MHz 資訊技術－無線射頻識別裝置符合性測試方法－第７部：４３３ＭＨｚ主動式空中介面通信之測試方法 |
|
|
|
CNS 12289
2017 Edition Reliability Assured Fixed Metal Film Resistors (H,J,K) (Established Failure Rate) 可靠度保證金屬皮膜固定電阻器（特性Ｈ，Ｊ及Ｋ）（故障率設定） |
Translated |
|
|
CNS 4762
2017 Edition Method of 5 Percent Sulfuric Acid Test for Stainless Steels 不銹鋼之５％硫酸腐蝕試驗法 |
|
|
|
CNS 6351-4
2017 Edition Oil of spearmint - Part 4: Scotch variety (Mentha×gracilis Sole) 綠薄荷油－第4部：蘇格蘭變種 |
|
|
|
CNS 7962
2017 Edition Test Code for Performance of Numerically Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
|
|
|
CNS 13590
2017 Edition Method of Test for Plastic Flammability - Oxygen Index Method 塑膠燃燒性試驗法–氧指數法 |
Translated |
|
|
CNS 15776-1
2017 Edition Energy management system application program interface (EMS-API) – Part 1: Guidelines and general requirements 能源管理系統應用程式介面－第1部：指導綱要及一般要求事項 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [370] [371] [372] [373] [374] [375] [376] |
