"m " CNS Standards List| Accuracy Inspection | Method Test | Needle Bar | Glossary Terms | Liquefied Petroleum | Preparation steel | Base paper | Method fractional | |
|
CNS 4700
1987 Edition Hexagon Head Bolts with Thread Approximately to Head and with Small Widths Across Flats 六角頭全螺紋螺栓（具小對面寬度） |
|
|
|
CNS 12087
1987 Edition method of Test for Fiber Optic Devices (FOPT-82 Fluid Penetration Test for Filled Fiber Optic Cable) 光纖裝置檢驗法（充膠光纜流體滲透試驗FOTP-82） |
|
|
|
CNS 10927
1987 Edition method of Test for Fiber Optic Devices (FOTP-28 Measuring Failure Point of Optical Waveguide Fiber) 光纖裝置檢驗法（光纖抗強拉度測量法FOTP-28） |
|
|
|
CNS 11874
1987 Edition Fixed mica Capacitors ( Type CM 35 ) 雲母固定電容器(CM35型) |
|
|
|
CNS 5774
1987 Edition Thermistor Rods, Insulated (Style TRC) 管形絕緣熱敏電阻器（型號ＴＲＣ） |
|
|
|
CNS 11938
1987 Edition Sprue Puller of molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 12077
1987 Edition minimum Rounded Radii and Drafts of Hot Forging Closed Die 熱鍛閉合模之最小圓角半徑與拔模斜度(角度) |
|
|
|
CNS 12084
1987 Edition method of Test for Fiber Optic Devices (FOPT-36 Twist Test for Fiber Optic Cable Assemblies 光纖裝置檢驗法（光纜組件扭力試驗FOTP-36） |
|
|
|
CNS 12085
1987 Edition method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information Transmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 12073
1987 Edition Die materials of Hot Forging Closed Die 熱鍛閉合模之模具材料 |
|
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting molds 壓鑄模用定位銷 |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 12070
1987 Edition Ejectorplate Guide Pin of Die Casting molds 壓鑄模用頂出板導銷 |
|
|
|
CNS 12069
1987 Edition Ejector Rod of Die Casting molds 壓鑄模用頂出桿 |
|
|
|
CNS 12068
1987 Edition Support of Die Casting molds 壓鑄模用支座 |
|
|
|
CNS 12007
1987 Edition method of Test for Helical Scanning Video Tape Recorders 螺線掃描錄放影機檢驗法 |
|
|
|
CNS 11993
1987 Edition method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 11992
1987 Edition method of Test for Fiber Optic Devices (FOTP-42 Optical Crosstalk in Fiber Optic Components) 光纖裝置檢驗法（光纖零組件內之串訊FOTP-42） |
|
|
|
CNS 5772
1987 Edition Thermistor Disks, Insulated (Style TDC) 盤形絕緣熱敏電阻器（型號ＴＤＣ） |
|
|
|
CNS 11939
1987 Edition Setting Plugs of molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 5773
1987 Edition Thermistor Rods, Non - Insulated (Style TRX) 管形無絕緣熱敏電阻器（型號ＴＲＸ） |
|
|
|
CNS 11937
1987 Edition Runner Pull Pins of molds for Plastics 塑膠型模用流道拉銷 |
|
|
|
CNS 11936
1987 Edition Stop Pins of molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 12086
1987 Edition method of Test for Fiber Optic Devices (FOPT-55 Method for Measuring the Coating Geometry of Optical Fibers) 光纖裝置檢驗法（光纖鍍層幾何形狀之測量法FOTP-55） |
|
|
|
CNS 6032
1987 Edition Alkaline Primary Cells and Batteries 鹼性一次電池 |
|
|
|
CNS 5992
1987 Edition Knockout Equipment for Press Dies 衝模用頂出裝置 |
|
|
|
CNS 12082
1987 Edition method of Test for Fiber Optic Devices (FOPT-30 Frequency Domain Measurement of Multimode Optical Fiber Information Transmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量FOTP-30） |
|
|
|
CNS 7642
1987 Edition method of Test for Fiber Optic Devices (Air Leakage Testing of Fiber Optic Component Seals) 光纖裝置檢驗法(光纖組件密封漏氣試驗FOTP-23) |
|
|
|
CNS 11935
1987 Edition Supporter of molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11934
1987 Edition Stop Bolts of molds for plastics 塑膠型模用止動螺栓 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [387] [388] [389] [390] [391] [392] [393] |
