",with " CNS Standards List |
|
CNS 7586
2020 Edition Remote Control Gear with Transmission Tubing for Manual Operation Protecting Hoods for Crown Gear Units, Slewable 遙遠操作傳導桿管（可擺動之冠狀齒輪傳動機構之保護罩） |
|
|
|
CNS 9567
2020 Edition Withdrawal Sleeves for Rolling Bearings 滾動軸承拔出套筒 |
|
|
|
CNS 493
2020 Edition Fine Whitworth Thread (Diameter Ranging From 20 to 189 mm, with Tip Clearance) 韋氏細螺紋（尖端有空隙，直徑自２０至１８９公釐） |
|
|
|
CNS 9571
2020 Edition Thrust Rings with Pin Holes Dimensions 具銷孔止推軸環尺度 |
|
|
|
CNS 394
2020 Edition Bearing Sleeve with Hard Lead Lever 軸承襯（嵌以硬鉛） |
|
|
|
CNS 5007
2020 Edition Rotating Tools with Parallel Shanks-Diameters of Shanks and Sizes Driving Squares 直柄旋轉刀具之柄徑及驅動方頭之尺寸 |
|
|
|
CNS 492
2020 Edition Whitworth Thread (Without Tip Clearance) 韋氏螺紋（尖端無空隙） |
|
|
|
CNS 20121
2020 Edition Event sustainability management systems − Requirements with guidance for use 會展及大型活動永續管理系統－附使用指引之要求事項 |
|
|
|
CNS 15200-3-4
2020 Edition Method of test for paints – Part 3–4: Film formability of paints – Evaluation of the compatibility of product with a surface to be painted 塗料一般試驗法－第３－４部：塗膜形成性－產品與被塗布面之適合性 |
|
|
|
CNS 15212-5
2020 Edition Clinical thermometers - Part 5: Performance of infra-red ear thermometers (with maximum device) 電子體溫計－第５部：紅外線耳溫計（具最大值裝置）的性能 |
|
|
|
CNS 159
2020 Edition Tab Washers (with Long Tap) 長舌墊圈 |
|
|
|
CNS 6810
2020 Edition Steering Locks with Ignition Switches for Automobiles 汽車用附起動開關之方向盤鎖 |
Translated |
|
|
CNS 9570
2020 Edition Thrust Rings with Keyway Dimensions 具鍵槽止推軸環尺度 |
|
|
|
CNS 8089
2020 Edition Drain Traps (Without Clean Cap) 落水管（不附清除蓋） |
Translated |
|
|
CNS 9072
2020 Edition Snap Rings for Bearings with Ring Groove 扣環（滾動軸承用） |
|
|
|
CNS 4576
2020 Edition Bolted Connections with Reduced Body; Survey and Installation 減徑柄螺栓之結合法（概覽，應用範圍與裝用實例） |
|
|
|
CNS 7572
2020 Edition Basic Rack Tooth Profile of Gear Tools for Cylindrical Gears with Involute Teeth for Fine Mechanics 漸開線圓柱齒輪切齒刀具之基準齒條齒廓（精細機械用） |
|
|
|
CNS 15027-2
2019 Edition Sound system equipment − Headphones and earphones associated with personal music players − Maximum sound pressure level measurement methodology − Part 2: Matching of sets with headphones if either or both are offered separately, or are offered as one pack 聲音系統設備－與個人音樂播放器相關之頭戴式耳機及耳戴式耳機－最大聲壓位準量測法－第2部：個人音樂 播放器與頭戴式耳機之匹配－兩者單獨提供或以套裝設備提供 |
|
|
|
CNS 15030-12
2019 Edition Classification and labelling of chemicals - Substances and mixtures which, in contact with water, emit flammable gases 化學品分類及標示－禁水性物質 |
Translated |
|
|
CNS 16113-1
2019 Edition Textiles − Methods for determination of certain aromatic amines derived from azo colorants − Part 1: Detection of the use of certain azo colorants accessible with and without extracting the fibres 紡織品－偶氮色料衍生特定芳胺的測定法－第1部：纖維經萃取與不經萃取偵測使用之特定偶氮色料 |
|
|
|
CNS 15027-3
2019 Edition Sound system equipment − Headphones and earphones associated with personal music players − Maximum sound pressure level measurement methodology − Part 3: Measurement method for sound dose management 聲音系統設備－與個人音樂播放器相關之頭戴式耳機及耳戴式耳機－最大聲壓位準量測法－第3部：聲音劑量管理之量測法 |
|
|
|
CNS 14934-3
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 3: Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≦16A per phase and not subject to conditional connection 電磁相容－限制值－第3部：每相額定電流在16 A以下且不屬於有條件連接之設備於公共低電壓電源系統中電壓改變、電壓變動及閃爍之限制值 |
|
|
|
CNS 1233
2019 Edition Method of Test for Flexural Strength of Concrete (Using Simple Beam with Third-point Loading) 混凝土抗彎強度試驗法（三分點載重法） |
Translated |
|
|
CNS 60335-2-114
2019 Edition Household and similar electrical appliances − Safety − Part 2-114: Particular requirements for self-balancing personal transport devices for use with batteries containing alkaline or other non-acid electrolytes 家用和類似用途電器－安全性－第2-114部：搭配含鹼性或其他非酸性電解質電池組使用之自主平衡式個人運輸裝置之個別規定 |
|
|
|
CNS 15027-1
2019 Edition Sound system equipment − Headphones and earphones associated with personal music players − Maximum sound pressure level measurement methodology − Part 1: General method for one package equipment 聲音系統設備－與個人音樂播放器相關之頭戴式耳機及耳戴式耳機－最大聲壓位準量測法－第1部：套裝設備之一般量測法 |
|
|
|
CNS 15562-10
2019 Edition Stationary training equipment − Part 10: Exercise bicycles with a fixed wheel or without freewheel, additional specific safety requirements and test methods 固定式訓練器材－第10部：具固定輪或無自由輪健身車之附加特定安全要求與試驗法 |
|
|
|
CNS 1234
2019 Edition Method of Test for Flexural Strength of Concrete (Using Simple Beam with Center-point Loading) 混凝土抗彎強度試驗法（中心點載重法） |
Translated |
|
|
CNS 16107-3
2019 Edition Hollow taper interface with flange contact surface − Part 3: Dimensions of shanks for stationary tools 具凸緣接觸面之空心錐度界面－第3部：固定式刀具之刀柄尺度 |
|
|
|
CNS 16107-4
2019 Edition Hollow taper interface with flange contact surface − Part 4: Dimensions of receivers for stationary tools 具凸緣接觸面之空心錐度界面－第4部：固定式刀具用接收器之尺度 |
|
|
|
CNS 15785-6
2019 Edition Tool holders with cylindrical shank − Part 6: Type E with cylindrical seat 具圓柱柄之刀具夾持器－第6 部：具圓柱形座之E 型 |
|
| Find out:672Items | To Page of: First -Previous-Next -Last | 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 |
