"35 " CNS Standards List| Casting moulds | Chemical Reagent | Amidosulfuric acid（reagent） | Chlorinated rubber | Polyester Staple | Filament lamps | Method Test | Soft Contact | |
|
CNS 358
2020 Edition Free Wheels for Bicycles 自行車（腳踏車）自由輪 |
Translated |
|
|
CNS 9351
2020 Edition Bushes for Plain Bearings Made of Artificial Carbon 滑動軸承軸襯–碳精製 |
|
|
|
CNS 15352
2020 Edition Hard anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之硬質陽極氧化膜 |
|
|
|
CNS 15356
2020 Edition Test method for continuity of anodic oxide coatings on aluminium and aluminium alloys - Copper sulphate test 鋁及鋁合金之陽極氧化膜連續性試驗法－硫酸銅試驗法 |
|
|
|
CNS 3561
2020 Edition Rubber, vulcanized or thermoplastic − Determination of rebound resilience 硫化或熱塑性橡膠－回彈性測定法 |
|
|
|
CNS 3586
2020 Edition Perlite Heat Insulating Sheet (Block) and Pipe 真珠岩保溫板（磚）及保溫管 |
Translated |
|
|
CNS 12835-5
2020 Edition Plastics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 4: Valves 燃氣用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 12835-3
2020 Edition Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) − Part 2: Pipes 燃氣用塑膠配管系統－聚乙烯(PE)－第3部：管件 |
|
|
|
CNS 60335-2-6
2020 Edition Household and similar electrical appliances − Safety − Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances 家用和類似用途電器－安全性－第2-6部：放置型爐灶、爐架、烤箱及類似電器之個別規定 |
|
|
|
CNS 15353-2
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Instrumental method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第２部：儀器測定法 |
|
|
|
CNS 60335-2-2
2020 Edition Household and similar electrical appliances − Safety − Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances 家用和類似用途電器－安全性－第2-2部：真空吸塵器及吸水清潔機之個別規定 |
|
|
|
CNS 13512
2020 Edition Masonry cement 墁砌水泥 |
|
|
|
CNS 13531
2020 Edition Glossary Cones 圓錐用語 |
|
|
|
CNS 8350
2020 Edition Punched Tape Variable Block Format for Contouring and Contouring/Positioning Numerically Controlled Machine Tools ( replaced by CNS 14726 ) 數值控制工具機孔帶用可變段格式（定位及直線切削控制用） |
|
|
|
CNS 4354
2020 Edition Finishes and tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 12835-4
2020 Edition Plastics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 3: Fittings 燃氣用塑膠配管系統－聚乙烯(PE)－第4部：閥 |
|
|
|
CNS 4235
2020 Edition Fasteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 13532
2020 Edition Conical Tapers 圓錐錐度 |
|
|
|
CNS 9352
2020 Edition Bushes for Plain Bearings Made From Dura Plastics 滑動軸承軸襯–熱硬性樹脂製 |
|
|
|
CNS 9354
2020 Edition Bushes for Plain Bearings, Press Bushes Made From Thermoplastics 滑動軸承軸襯–熱塑性塑膠製 |
|
|
|
CNS 15353-1
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart scale method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第１部：圖表比例尺法 |
|
|
|
CNS 4935
2020 Edition Epoxy Resin Non-Zinc Primer 環氧樹脂非鋅底漆 |
Translated |
|
|
CNS 13534
2020 Edition System of Cone Tolerances 圓錐公差制度 |
|
|
|
CNS 5435
2020 Edition Dimensions of Starter Pinions and Ring Gears for Automobiles 汽車用起動電動機小齒輪及環形齒輪之尺度 |
|
|
|
CNS 499
2020 Edition ISO Metric Fine Screw Threads (Diameters From 1 to 3.5mm and Pitches 0.2 to 0.35mm) 公制細螺紋2（ISO制）（標稱直徑1至3.5公釐，螺距0.2至0.35公釐） |
Translated |
|
|
CNS 3564-3
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 3: Determination of low temperature stiffening (Gehman test) 硫化或熱塑性橡膠−低溫性質之測定－第3部：低溫剛度測定法(吉門試驗) |
|
|
|
CNS 13536
2020 Edition Cone Fits 圓錐配合 |
|
|
|
CNS 60335-2-90
2020 Edition Household and similar electrical appliances − Safety − Part 2-90: Particular requirements for commercial microwave ovens 家用和類似用途電器－安全性－第2-90部：商用微波爐之個別規定 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 13533
2020 Edition Deviations for Center Distances 中心距離許可差 |
|
| Find out:661Items | To Page of: First -Previous-Next -Last | 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 |
