"35 " CNS Standards List |
|
CNS 3590
2020 Edition Method of Test for Normal Consisteney of Hydraulic Cement 水硬性水泥之正常稠度檢驗法 |
|
|
|
CNS 3542
2020 Edition Forged shackles for general lifting purposes – Dee shackles and bow shackles 一般起重吊掛用鍛造鉤環－D形鉤環及弓形鉤環 |
|
|
|
CNS 2352
2020 Edition Standard Classification of High-Alumina Brick 高鋁耐火磚分級標準 |
Translated |
|
|
CNS 15354
2020 Edition Test methods for dielectric strength of anodic oxide coatings on aluminium and aluminium alloys 鋁及鋁合金之陽極氧化膜絕緣性試驗法 |
|
|
|
CNS 3586
2020 Edition Perlite Heat Insulating Sheet (Block) and Pipe 真珠岩保溫板（磚）及保溫管 |
Translated |
|
|
CNS 9351
2020 Edition Bushes for Plain Bearings Made of Artificial Carbon 滑動軸承軸襯–碳精製 |
|
|
|
CNS 12835-5
2020 Edition Plastics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 4: Valves 燃氣用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 16135
2020 Edition Test method for determining tensile properties of geogrids by the single or multi-rib tensile method 地工格網抗拉特性－單肋條或多肋條拉伸試驗法 |
|
|
|
CNS 60335-2-90
2020 Edition Household and similar electrical appliances − Safety − Part 2-90: Particular requirements for commercial microwave ovens 家用和類似用途電器－安全性－第2-90部：商用微波爐之個別規定 |
|
|
|
CNS 15353-1
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart scale method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第１部：圖表比例尺法 |
|
|
|
CNS 9352
2020 Edition Bushes for Plain Bearings Made From Dura Plastics 滑動軸承軸襯–熱硬性樹脂製 |
|
|
|
CNS 8350
2020 Edition Punched Tape Variable Block Format for Contouring and Contouring/Positioning Numerically Controlled Machine Tools ( replaced by CNS 14726 ) 數值控制工具機孔帶用可變段格式（定位及直線切削控制用） |
|
|
|
CNS 358
2020 Edition Free Wheels for Bicycles 自行車（腳踏車）自由輪 |
Translated |
|
|
CNS 60335-2-2
2020 Edition Household and similar electrical appliances − Safety − Part 2-2: Particular requirements for vacuum cleaners and water-suction cleaning appliances 家用和類似用途電器－安全性－第2-2部：真空吸塵器及吸水清潔機之個別規定 |
|
|
|
CNS 4835
2020 Edition Edible palm kernel oil 食用棕櫚仁油 |
|
|
|
CNS 359
2020 Edition Hub Cogs for Bicycles 自行車（腳踏車）小鏈輪 |
|
|
|
CNS 3564-2
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 2: Determination of low-temperature brittleness 硫化或熱塑性橡膠－低溫性質之測定－第2部：低溫脆性測定法 |
|
|
|
CNS 4354
2020 Edition Finishes and tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 4935
2020 Edition Epoxy Resin Non-Zinc Primer 環氧樹脂非鋅底漆 |
Translated |
|
|
CNS 499
2020 Edition ISO Metric Fine Screw Threads (Diameters From 1 to 3.5mm and Pitches 0.2 to 0.35mm) 公制細螺紋2（ISO制）（標稱直徑1至3.5公釐，螺距0.2至0.35公釐） |
Translated |
|
|
CNS 3564-4
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 4: Determination of low-temperature retraction (TR test) 硫化或熱塑性橡膠－低溫性質之測定－第4部：低溫回縮測定法(TR試驗) |
|
|
|
CNS 60335-2-6
2020 Edition Household and similar electrical appliances − Safety − Part 2-6: Particular requirements for stationary cooking ranges, hobs, ovens and similar appliances 家用和類似用途電器－安全性－第2-6部：放置型爐灶、爐架、烤箱及類似電器之個別規定 |
|
|
|
CNS 13532
2020 Edition Conical Tapers 圓錐錐度 |
|
|
|
CNS 15356
2020 Edition Test method for continuity of anodic oxide coatings on aluminium and aluminium alloys - Copper sulphate test 鋁及鋁合金之陽極氧化膜連續性試驗法－硫酸銅試驗法 |
|
|
|
CNS 9354
2020 Edition Bushes for Plain Bearings, Press Bushes Made From Thermoplastics 滑動軸承軸襯–熱塑性塑膠製 |
|
|
|
CNS 4235
2020 Edition Fasteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 13512
2020 Edition Masonry cement 墁砌水泥 |
|
|
|
CNS 3576
2020 Edition Method of test for ash from petroleum products 石油產品灰分試驗法 |
|
|
|
CNS 13536
2020 Edition Cone Fits 圓錐配合 |
|
|
|
CNS 13535
2020 Edition Angles and Slopes on Prisms 機械用稜柱角度及稜柱斜度 |
|
| Find out:661Items | To Page of: First -Previous-Next -Last | 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 |
