"3 " CNS Standards List |
|
CNS 8483
2020 Edition Control Cables for Motor - Cycle 兩輪機車用操縱線 |
Translated |
|
|
CNS 7397
2020 Edition Method of test for fiber glass products 玻璃纖維製品檢驗法 |
|
|
|
CNS 4235
2020 Edition Fasteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 4539
2020 Edition Terms relating to the manufacture of fasteners 結件詞彙（製造方法） |
|
|
|
CNS 14503-1
2020 Edition Evaluation methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 4530
2020 Edition Terms Relating to the Head of Fasteners 結件頭部詞彙 |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 8131
2020 Edition Oil of bergamot [Citrus aurantium L. subsp. bergamia (Wight et Arnott) Engler], Italian type 義大利香柑油（壓榨法） |
|
|
|
CNS 3743
2020 Edition Series 1 freight containers - Classification, dimensions and ratings 第一類貨櫃－分類、尺度及額定質量 |
|
|
|
CNS 13626
2020 Edition Steel drums - Removable head (open head) 鋼製圓桶－掀蓋式 |
|
|
|
CNS 12843
2020 Edition Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 2392
2020 Edition Trough Type Clay-Burnt Tiles for Building 建築用槽形土燒瓦 |
Translated |
|
|
CNS 4354
2020 Edition Finishes and tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 361
2020 Edition Rear Hubs for Bicycles 自行車（腳踏車）後輪轂 |
Translated |
|
|
CNS 12983
2020 Edition Standard Substances for Volumetric Analysis 容量分析用標準試藥 |
|
|
|
CNS 9341
2020 Edition Oil Seals 油封 |
|
|
|
CNS 6903
2020 Edition Cable Terminals for Automobiles (Type LB) 汽車用電線端子（橫接環眼型） |
|
|
|
CNS 15423-2
2020 Edition Equipment for water supply service– Part 2: Test methods of low temperature resistant 自來水用器具－第2部：耐寒試驗法 |
|
|
|
CNS 3-16
2020 Edition Engineering Drawing (Geometrical Tolerancing - Principles and Methods of Verification) 工程製圖（幾何公差–檢測原理與方法） |
|
|
|
CNS 4832
2020 Edition Edible cottonseed oil 食用棉籽油 |
|
|
|
CNS 14306-4
2020 Edition Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates (Method for the calibration of ISO surface profile comparators and for the determination of surface pro 塗料及有關製品塗裝前之鋼面處理－噴射清理鋼面之表面粗糙度特性（ISO表面輪廓參比標準板校正方法及剖面曲線測定法－觸針法） |
|
|
|
CNS 13601
2020 Edition Method of test for flammability of children's sleepwear 兒童睡衣防焰性試驗法 |
|
|
|
CNS 3981
2020 Edition Dimensions of tapping screws thread 自攻螺釘螺紋尺度 |
|
|
|
CNS 20301
2020 Edition Health informatics − Health cards − General characteristics 健康資訊學－健康卡－一般特性 |
|
|
|
CNS 12938
2020 Edition Vitrified clay pipes and fittings and pipe joints for drains and sewers 排水及污水用瓷化黏土管以及其配件與管接頭 |
|
|
|
CNS 7031
2020 Edition Dimensions of Hitches for Agricultural Tractors 農業用曳引機繫扣之尺度 |
|
|
|
CNS 3389
2020 Edition Method for Calculating Viscosity Index from Kinematic Viscosity at 40 and 100 Degree C 由40°及100℃動黏度計算黏度指數之方法 |
|
|
|
CNS 16143-2
2020 Edition Railway applications − Track − Performance requirements for fastening systems − Part 2: Fastening systems for concrete sleepers 鐵路應用－軌道－扣件系統之性能要求－第2部：混凝土軌枕用扣件系統 |
|
|
|
CNS 8407-3
2020 Edition Test methods for sealing quality of anodic oxide coatings on aluminium and aluminium alloys - Part 3: Admittance test method 鋁及鋁合金之陽極氧化膜封孔度試驗法－第３部：導納試驗法 |
|
|
|
CNS 500
2020 Edition ISO Metric Fine Screw Threads (Diameters from 4 to 8mm and Pitches 0.5 to 0.75mm) 公制細螺紋3（ISO制）（標稱直徑4至8公釐，螺距0.5至0.75公釐） |
Translated |
| Find out:6360Items | To Page of: First -Previous-Next -Last | [35] [36] [37] [38] [39] [40] [41] |
