"F " CNS Standards List| Lead Frames | Glossary Terms | Screwed Bronze | Method Test | Information Technology | Glassfiber reinforced | Hand held | Photography Processing | |
|
CNS 4665
1984 Edition Insert Nuts Heavy Type For Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 6410
1984 Edition Calculation oF Load Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 6411
1984 Edition Calculation oF Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 10734
1984 Edition Method oF Test for the Plastic Rims of Bicycle 平車或跑車型自行車塑膠輪圈檢驗法 |
|
|
|
CNS 6412
1984 Edition Calculation oF Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 10735
1984 Edition Plastic Rims For Bicycles 平車或跑車型自行車塑膠輪圈 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions oF Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 6414
1984 Edition Basic Rack oF Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 10005
1984 Edition General Rules For Photoelectric Emission Spectrochemical Analysis of Metallic Materials 金屬材料之光電式發光光譜分析法通則 |
|
|
|
CNS 6415
1984 Edition Series oF modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves and Bore RelieFs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 11153
1984 Edition Method oF Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 5298
1984 Edition Hose Clamps For the Lower Pressure 低壓軟管夾 |
|
|
|
CNS 11151
1984 Edition Method oF Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 11070
1984 Edition General Rules oF Determination for Carbon in Metallic Materials 金屬材料中碳定量法通則 |
|
|
|
CNS 5027
1984 Edition Control Timers For Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 11112
1984 Edition Methods oF Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 10786
1984 Edition Test Code For Performance of Drum Sanders 圓筒砂光機動態檢驗法 |
|
|
|
CNS 10778
1984 Edition Combustion Test For Cigaratte Paper 捲菸紙燃燒速度試驗法 |
Translated |
|
|
CNS 10761
1984 Edition Method oF Test for Surface Wax on Waxed Paper or Paperboard 蠟紙及蠟紙板之表面蠟量試驗法 |
Translated |
|
|
CNS 11072
1984 Edition Method oF X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5279
1984 Edition Dimensions oF Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 7344
1984 Edition Crowbars (For Fire Fighting Use) 撬桿（消防用） |
|
|
|
CNS 4731
1984 Edition Knurled Nuts For Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 5266
1984 Edition Series oF Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 5267
1984 Edition Accuracy oF Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 11158
1984 Edition Tungsten-Carbide Bits and Rod For Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 5268
1984 Edition Accuracy oF Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths oF Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths oF Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [404] [405] [406] [407] [408] [409] [410] |
