"f " CNS Standards List |
|
CNS 6415
1984 Edition Series of modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 11158
1984 Edition Tungsten-Carbide Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 11112
1984 Edition Methods of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 10761
1984 Edition Method of Test for Surface Wax on Waxed Paper or Paperboard 蠟紙及蠟紙板之表面蠟量試驗法 |
Translated |
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 10735
1984 Edition Plastic Rims for Bicycles 平車或跑車型自行車塑膠輪圈 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 10734
1984 Edition Method of Test for the Plastic Rims of Bicycle 平車或跑車型自行車塑膠輪圈檢驗法 |
|
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
|
|
CNS 11151
1984 Edition Method of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 4731
1984 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 5276
1984 Edition factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 7344
1984 Edition Crowbars (for Fire Fighting Use) 撬桿（消防用） |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5026
1984 Edition Welding Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 10225
1984 Edition Test Code for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 4730
1984 Edition Lifting Eye Nuts 圓形環首螺帽 |
|
|
|
CNS 5022
1984 Edition Thyristorstack for Welding Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5280
1984 Edition Helix Angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [404] [405] [406] [407] [408] [409] [410] |
