"3, " CNS Standards List| Band Saw | Method Test | Methods Test | Ferrophosphorus | Determination Plastic | Method Test | Method test | Octave Third | |
|
CNS 8734
2020 Edition Spices and condiments − Chillies and capsicums, whole or ground (powdered) 香辛料及調味料－全果狀或粉狀番椒與辣椒 |
|
|
|
CNS 1903
2020 Edition Potassium Phosphate, Monobasic Potassium Biphosphate Soerenson's Potassium Phosphate 化學試藥（玫瑰紅酸鉀） |
|
|
|
CNS 7534
2020 Edition Personal protective equipment for work positioning and prevention of falls from a height − Belts for work positioning and restraint and work positioning lanyards 工作定位及防止由高處墜落之個人防護具－工作定位與限制帶及工作定位索 |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 13379
2020 Edition Petroleum ether 石油醚 |
|
|
|
CNS 4531
2020 Edition Terms Relating to the Neck of Fasteners 結件頸部詞彙 |
|
|
|
CNS 13138
2020 Edition Safety Standards for Construction of Band Saws With Carriages 送材車式帶鋸機之構造安全基準 |
|
|
|
CNS 331
2020 Edition Hand-Wheels with Crooked Rims and Straight Arms 手輪（曲環，直輻） |
|
|
|
CNS 362
2020 Edition Spokes for Bicycles 自行車（腳踏車）輻絲 |
Translated |
|
|
CNS 4836
2020 Edition Edible palm oil 食用棕櫚油 |
|
|
|
CNS 3-3
2020 Edition Engineering Drawing (Method of indicating surface texture on drawings) 工程製圖(表面織構符號) |
|
|
|
CNS 13532
2020 Edition Conical Tapers 圓錐錐度 |
|
|
|
CNS 13168
2020 Edition Safety Standards for Construction of Routers 花鉋機之構造安全基準 |
|
|
|
CNS 14389
2020 Edition Methods of measuring for specific surface area of fine ceramic powders by gas adsorption 精密陶瓷粉體BET氣體吸附比表面積測定法 |
|
|
|
CNS 4354
2020 Edition Finishes and tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 15345-2
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedure 機械安全－降低由機械釋放有害性物質對健康造成之風險－第２部：查證程序之方法 |
|
|
|
CNS 15353-2
2020 Edition Test methods for image clarity of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Instrumental method 鋁及鋁合金之陽極氧化膜影像清晰度試驗法－第２部：儀器測定法 |
|
|
|
CNS 14132
2020 Edition Inorganic zinc rich primer (Water - borne type) 無機鋅粉底漆（水性） |
|
|
|
CNS 2031
2020 Edition Uranyl Acetate 化學試藥（醋酸鈾醯） |
|
|
|
CNS 3220-3
2020 Edition Sanitary ceramic ware- Washbasin 衛生陶瓷器—洗面盆 |
Translated |
|
|
CNS 499
2020 Edition ISO Metric Fine Screw Threads (Diameters From 1 to 3.5mm and Pitches 0.2 to 0.35mm) 公制細螺紋2（ISO制）（標稱直徑1至3.5公釐，螺距0.2至0.35公釐） |
Translated |
|
|
CNS 15317-2
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 2: Pipes 冷熱水輸送用交連聚乙烯管－第２部：管 |
|
|
|
CNS 9380
2020 Edition Lead Wires for Automobiles Electrical Equipments 汽車用電裝備之附屬導線 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 15319-9-1
2020 Edition Sodium hydroxide for industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 60335-2-90
2020 Edition Household and similar electrical appliances − Safety − Part 2-90: Particular requirements for commercial microwave ovens 家用和類似用途電器－安全性－第2-90部：商用微波爐之個別規定 |
|
|
|
CNS 15200-4-3
2020 Edition Methods of test for paints - Part 4-3: Visual characteristics of film - Colorimetry (Principles) 塗料一般試驗法－第４－３部：塗膜視覺特性－測色（原理） |
|
|
|
CNS 8483
2020 Edition Control Cables for Motor - Cycle 兩輪機車用操縱線 |
Translated |
|
|
CNS 15263
2020 Edition Method of test for light duty vehicle lateral collision 小型車之側面碰撞試驗法 |
|
|
|
CNS 3389
2020 Edition Method for Calculating Viscosity Index from Kinematic Viscosity at 40 and 100 Degree C 由40°及100℃動黏度計算黏度指數之方法 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [36] [37] [38] [39] [40] [41] [42] |
