"3 3 " CNS Standards List| Aseptic processing | Electrolytic zinc | Method test | Inner tubes | Determination the | Standard test | Robots robotic | Management the | |
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 362
2020 Edition Spokes for Bicycles 自行車（腳踏車）輻絲 |
Translated |
|
|
CNS 11738
2020 Edition Method of Test for Specific Gravity and True Porosity of Insulating Fire Bricks 絕熱耐火磚比重及真孔隙度試驗法 |
|
|
|
CNS 14132
2020 Edition Inorganic zinc rich primer (Water - borne type) 無機鋅粉底漆（水性） |
|
|
|
CNS 12843
2020 Edition Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 1853
2020 Edition Phenol red (Reagent) 酚紅（試藥） |
|
|
|
CNS 4235
2020 Edition Fasteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 4370
2020 Edition Round Thread with Clearance and Flat Flank with Pitch 7mm (Limits of Size and Deviation--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙淺螺腹、螺距為７ｍｍ之限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 14104-3
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 2: Method of describing lower limb amputation stumps 義肢學與矯具學－肢體缺陷－第３部：上肢截肢之描述 |
|
|
|
CNS 7593
2020 Edition Helical Springs Made of Round Wire Dimensions for Cold Coiled Compression Springs of Less Than 0.5 mm Wire Diameter 冷捲成形壓縮螺旋彈簧（簧線直徑小於０．５ｍｍ之構造尺度） |
|
|
|
CNS 8483
2020 Edition Control Cables for Motor - Cycle 兩輪機車用操縱線 |
Translated |
|
|
CNS 1913
2020 Edition Quinalizarin Tetrahydroxyanthraquinone 化學試藥（四羥基蔥醌） |
|
|
|
CNS 15317-2
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 2: Pipes 冷熱水輸送用交連聚乙烯管－第２部：管 |
|
|
|
CNS 9173
2020 Edition Gas-Filled Single Tube Shock Absorbers for Automobiles 汽車用單管充氣減震器 |
Translated |
|
|
CNS 3-18
2020 Edition Engineering drawing (Symbolic presentation and indication of adhesive, fold and pressed joints) 工程製圖（板金膠合、鉤合、壓合符號表示法） |
|
|
|
CNS 15319-9-1
2020 Edition Sodium hydroxide for industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 331
2020 Edition Hand-Wheels with Crooked Rims and Straight Arms 手輪（曲環，直輻） |
|
|
|
CNS 2392
2020 Edition Trough Type Clay-Burnt Tiles for Building 建築用槽形土燒瓦 |
Translated |
|
|
CNS 15317-1
2020 Edition Crosslinked polyethylene (PE-X) pipe for hot and cold water conveyance - Part 1: General 冷熱水輸送用交連聚乙烯管－第１部：通則 |
|
|
|
CNS 3786
2020 Edition Method of Test for Grinding Wheels 研磨輪檢驗法 |
Translated |
|
|
CNS 1938
2020 Edition Sodium 化學試藥（鈉） |
|
|
|
CNS 9380
2020 Edition Lead Wires for Automobiles Electrical Equipments 汽車用電裝備之附屬導線 |
|
|
|
CNS 332
2020 Edition Hand Wheels with Crooked Rims and Curved Arms 手輪（曲環，斜輻） |
|
|
|
CNS 13534
2020 Edition System of Cone Tolerances 圓錐公差制度 |
|
|
|
CNS 7553
2020 Edition Slip-on Welding Steel Pipe Flanges (5 kgf/㎠) 滑入熔接式鋼製管凸緣（5 kgf/㎠） |
|
|
|
CNS 14316
2020 Edition General rules of the sample preparation for particle size analysis of fine ceramic raw powder 精密陶瓷原料粒徑分布測定之試樣調製通則 |
|
|
|
CNS 9352
2020 Edition Bushes for Plain Bearings Made From Dura Plastics 滑動軸承軸襯–熱硬性樹脂製 |
|
|
|
CNS 15345-2
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedure 機械安全－降低由機械釋放有害性物質對健康造成之風險－第２部：查證程序之方法 |
|
|
|
CNS 7893
2020 Edition Windshield Wiper Motors for Automobiles 汽車用雨刷馬達 |
|
|
|
CNS 14637-4
2020 Edition Test code for machine tools − Part 4: Circular tests for numerically controlled machine tools 工具機試驗規範－第4 部:數值控制工具機之圓弧試驗 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [36] [37] [38] [39] [40] [41] [42] |
