"3 " CNS Standards List| Method test | Clutch Facings | Indoor air | Electric Soldering | Resinoid Grinding | Method Test | Tinners | Hand held | |
|
CNS 4235
2020 Edition Fasteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 12983
2020 Edition Standard Substances for Volumetric Analysis 容量分析用標準試藥 |
|
|
|
CNS 15319-9-1
2020 Edition Sodium hydroxide for industrial use - Part 9-1: Determination of magnesium content – Flame atomic absorption spectrometry 工業用氫氧化鈉－第９-１部：鎂含量測定法－原子吸收光譜分析法 |
|
|
|
CNS 5435
2020 Edition Dimensions of Starter Pinions and Ring Gears for Automobiles 汽車用起動電動機小齒輪及環形齒輪之尺度 |
|
|
|
CNS 8930
2020 Edition Switchgears, Contact - Spring Washers 加強型彈簧墊圈（電器開關–接觸用） |
|
|
|
CNS 4539
2020 Edition Terms relating to the manufacture of fasteners 結件詞彙（製造方法） |
|
|
|
CNS 3564-2
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 2: Determination of low-temperature brittleness 硫化或熱塑性橡膠－低溫性質之測定－第2部：低溫脆性測定法 |
|
|
|
CNS 15392
2020 Edition Coffee triers 咖啡取樣器 |
|
|
|
CNS 13158
2020 Edition Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipes for Water Works 自來水用丙烯腈–丁二烯–苯乙烯（ABS）塑膠管 |
Translated |
|
|
CNS 8386
2020 Edition Mechanical Fuel Pumps for Automobiles 汽車用機械驅動式燃料泵 |
|
|
|
CNS 15823
2020 Edition Measurement of antibacterial activity on plastics and other non-porous surfaces 塑膠及非多孔表面抗菌性測定法 |
|
|
|
CNS 3786
2020 Edition Method of Test for Grinding Wheels 研磨輪檢驗法 |
Translated |
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 9354
2020 Edition Bushes for Plain Bearings, Press Bushes Made From Thermoplastics 滑動軸承軸襯–熱塑性塑膠製 |
|
|
|
CNS 30101
2020 Edition Information technology − Sensor networks − Sensor network and its interfaces for smart grid system 資訊技術－感測器網路－ 感測器網路及其與智慧電網系統之介面 |
|
|
|
CNS 15320
2020 Edition Determination of the ultimate anaerobic biodegradation of plastic materials in an aqueous system - Method by measurement of biogas production 塑膠材料在水溶液系統中最終厭氧生物分解度測定法－生物生成氣體量測法 |
|
|
|
CNS 61439-4
2020 Edition Low-voltage switchgear and controlgear assemblies − Part 4: Particular requirements for assemblies for construction sites (ACS) 低電壓開關裝置及控制裝置組裝品－第4部：建築工地用組裝品(ACS)之個別要求 |
|
|
|
CNS 3321
2020 Edition Magnesia Brick 鎂磚 |
Translated |
|
|
CNS 14473
2020 Edition Method of test for flash point by small scale closed tester 閃點測定法(迷你閉杯式法) |
|
|
|
CNS 1973
2020 Edition Sodium Nitroferricyanide 化學試藥（亞硝醯鐵氰化鈉） |
|
|
|
CNS 3564-4
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 4: Determination of low-temperature retraction (TR test) 硫化或熱塑性橡膠－低溫性質之測定－第4部：低溫回縮測定法(TR試驗) |
|
|
|
CNS 16135
2020 Edition Test method for determining tensile properties of geogrids by the single or multi-rib tensile method 地工格網抗拉特性－單肋條或多肋條拉伸試驗法 |
|
|
|
CNS 7733
2020 Edition Chemical Reagent (Sodium Perchlorate Monohydrate) 化學試藥（一水合過氯酸鈉） |
|
|
|
CNS 7703
2020 Edition Leather - Physical and mechanical tests - Determination of water vapour absorption 皮革－物性及機械性質測試－吸濕度試驗法 |
|
|
|
CNS 13269
2020 Edition Safety Standards for Construction of Rip Saw and Gang Rip Saw 單片縱鋸機及多片縱鋸機之構造安全基準 |
|
|
|
CNS 1761
2020 Edition 3-Methyl-1-butanol (Reagent) 化學試藥（３–甲基–１–丁醇） |
|
|
|
CNS 4239
2020 Edition Marking of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之標示 |
Translated |
|
|
CNS 1635
2020 Edition Carbon Tetrachloride (Chemical Reagent) 化學試藥（四氯化碳） |
|
|
|
CNS 14314
2020 Edition Method of test for particle density of fine ceramic powder 精密陶瓷粉末粒子密度測定法 |
|
|
|
CNS 15832-2-3
2020 Edition Method of test for paint components − Part 2-3: Component analysis in solvent soluble matter − Boiling range 塗料成分試驗法－第2-3 部：溶劑可溶物中成分分析－沸點範圍 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [37] [38] [39] [40] [41] [42] [43] |
