"3 3 " CNS Standards List| 600 V | Marine Bronze | Method Test | Method test | Method Test | Magneto Ball | Lot Control | Household similar | |
|
CNS 15345-2
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedure 機械安全－降低由機械釋放有害性物質對健康造成之風險－第２部：查證程序之方法 |
|
|
|
CNS 15423-2
2020 Edition Equipment for water supply service– Part 2: Test methods of low temperature resistant 自來水用器具－第2部：耐寒試驗法 |
|
|
|
CNS 14132
2020 Edition Inorganic zinc rich primer (Water - borne type) 無機鋅粉底漆（水性） |
|
|
|
CNS 14503-1
2020 Edition Evaluation methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 1913
2020 Edition Quinalizarin Tetrahydroxyanthraquinone 化學試藥（四羥基蔥醌） |
|
|
|
CNS 3299-11
2020 Edition Methods of test for ceramic tiles – Part 11: Determination of lead and cadmium given off by glazed tiles 陶瓷面磚試驗法－第１１部：施釉面磚溶出鉛及鎘定量試驗法 |
|
|
|
CNS 12983
2020 Edition Standard Substances for Volumetric Analysis 容量分析用標準試藥 |
|
|
|
CNS 15423-5
2020 Edition Equipment for water supply service – Part 5: Test methods of destruction by vacuum pressure 自來水用器具－第5部：負壓破壞試驗法 |
|
|
|
CNS 499
2020 Edition ISO Metric Fine Screw Threads (Diameters From 1 to 3.5mm and Pitches 0.2 to 0.35mm) 公制細螺紋2（ISO制）（標稱直徑1至3.5公釐，螺距0.2至0.35公釐） |
Translated |
|
|
CNS 8350
2020 Edition Punched Tape Variable Block Format for Contouring and Contouring/Positioning Numerically Controlled Machine Tools ( replaced by CNS 14726 ) 數值控制工具機孔帶用可變段格式（定位及直線切削控制用） |
|
|
|
CNS 2031
2020 Edition Uranyl Acetate 化學試藥（醋酸鈾醯） |
|
|
|
CNS 7553
2020 Edition Slip-on Welding Steel Pipe Flanges (5 kgf/㎠) 滑入熔接式鋼製管凸緣（5 kgf/㎠） |
|
|
|
CNS 14389
2020 Edition Methods of measuring for specific surface area of fine ceramic powders by gas adsorption 精密陶瓷粉體BET氣體吸附比表面積測定法 |
|
|
|
CNS 15231
2020 Edition Oil of Citrus － Determination of CD value by ultraviolet spectrometric analysis 柑橘油—紫外光譜ＣＤ值測定法 |
|
|
|
CNS 4235
2020 Edition Fasteners－Acceptance inspection 結件之允收檢驗 |
|
|
|
CNS 332
2020 Edition Hand Wheels with Crooked Rims and Curved Arms 手輪（曲環，斜輻） |
|
|
|
CNS 9173
2020 Edition Gas-Filled Single Tube Shock Absorbers for Automobiles 汽車用單管充氣減震器 |
Translated |
|
|
CNS 9983
2020 Edition Hose Clamps for Automobiles 汽車用軟管夾 |
|
|
|
CNS 2013
2020 Edition Tetraethylammonium Hydroxide 化學試藥（氫氧化四乙銨） |
|
|
|
CNS 13534
2020 Edition System of Cone Tolerances 圓錐公差制度 |
|
|
|
CNS 3333
2020 Edition Zinc alloy ingots intended for castings 鑄造用鋅合金錠 |
|
|
|
CNS 2392
2020 Edition Trough Type Clay-Burnt Tiles for Building 建築用槽形土燒瓦 |
Translated |
|
|
CNS 13379
2020 Edition Petroleum ether 石油醚 |
|
|
|
CNS 62282-3-201
2020 Edition Fuel cell technologies − Part 3-201: Stationary fuel cell power systems − Performance test methods for small fuel cell power systems 燃料電池技術－第3-201部：定置型燃料電池發電系統－小型燃料電池發電系統之性能試驗法 |
|
|
|
CNS 3564-1
2020 Edition Rubber, vulcanized or thermoplastic − Determination of low-temperature properties − Part 1: General introduction and guide 硫化或熱塑性橡膠－低溫性質之測定－第1部：一般事項及指引 |
|
|
|
CNS 8943
2020 Edition Tyre Valve Stems for Automobiles 汽車輪胎氣門嘴本體 |
Translated |
|
|
CNS 3063
2020 Edition Slide Glasses for Microscope 顯微鏡用載玻璃 |
|
|
|
CNS 5435
2020 Edition Dimensions of Starter Pinions and Ring Gears for Automobiles 汽車用起動電動機小齒輪及環形齒輪之尺度 |
|
|
|
CNS 9354
2020 Edition Bushes for Plain Bearings, Press Bushes Made From Thermoplastics 滑動軸承軸襯–熱塑性塑膠製 |
|
|
|
CNS 2737
2020 Edition Measurement of the maximum speed for motor vehicles 機動車輛最高速率測定法 |
|
| Find out:6360Items | To Page of: First -Previous-Next -Last | [37] [38] [39] [40] [41] [42] [43] |
