"D " CNS Standards List |
|
CNS 11154
1984 Edition Grease Guns-Rush Type HanD Guns 手用衝壓式黃油槍 |
|
|
|
CNS 5285
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5277
1984 Edition CylinDrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5028
1984 Edition Rectifier Type DC Arc Welding Machines with Drooping Characteristic 穩流整流式直流電弧電焊機 |
|
|
|
CNS 11071
1984 Edition Emission-Spectroscopic Analysis for Carbon Steel anD Low Alloy Steel 碳鋼及低合金鋼之發光光譜分析法 |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance WelDing Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 11158
1984 Edition Tungsten-CarbiDe Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 6415
1984 Edition Series of moDules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 11157
1984 Edition Lubrication Holes, Grooves anD Bore Reliefs 潤滑孔、潤滑槽、潤滑坑 |
|
|
|
CNS 11072
1984 Edition MethoD of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5030
1984 Edition Projection WelDing Machine 凸壓電焊機 |
|
|
|
CNS 11151
1984 Edition MethoD of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 5284
1984 Edition ADdendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 10006
1984 Edition MethoD for Photoelectric Emission Spectrochemical Analysis of Iron And Steel 鐵及鋼之光電式發光光譜分析法 |
|
|
|
CNS 5283
1984 Edition Accuracy of CylinDrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 2388
1984 Edition MethoD of Test for Combustion Rate of Cigarette Paper 捲菸紙燃燒率試驗法 |
Translated |
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 5026
1984 Edition WelDing Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 11112
1984 Edition MethoDs of Chemical Analysis for Lead Ingot 鉛錠分析法 |
|
|
|
CNS 5280
1984 Edition Helix Angles for CylinDrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 11159
1984 Edition Tungsten-CarbiDe Tip Core Drills 碳化鎢鑽刃留心鑽頭 |
|
|
|
CNS 1419
1984 Edition MethoD of Test for Acetone 丙酮檢驗法 |
|
|
|
CNS 6410
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 11153
1984 Edition MethoD of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
|
|
CNS 6412
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis for Pig Iron anD Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator OperateD) 絕緣電阻計（發電機式） |
|
|
|
CNS 10849
1984 Edition Screw ThreaDs of Valves for High Pressure Gas Cylider 高壓鋼瓶閥螺紋標準 |
Translated |
|
|
CNS 10911
1984 Edition MethoD of Test for Microswitches 微動開關試驗法 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [418] [419] [420] [421] [422] [423] [424] |
