"D C " CNS Standards List| Method test | Method Test | Electrical apparatus | Method determination | Tempered glass | Wooden walking | Micro Hardness | General Rules | |
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 6415
1984 Edition Series of modules for Straight Bevel Gears 齒輪模數（直齒傘齒輪） |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5022
1984 Edition Thyristorstack for Welding Machine 電焊機用閘流調節器 |
Translated |
|
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 2388
1984 Edition Method of Test for Combustion Rate of Cigarette Paper 捲菸紙燃燒率試驗法 |
Translated |
|
|
CNS 6412
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 10761
1984 Edition Method of Test for Surface Wax on Waxed Paper or Paperboard 蠟紙及蠟紙板之表面蠟量試驗法 |
Translated |
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 4732
1984 Edition Knurled Nuts with Ring 有環滾紋螺帽 |
|
|
|
CNS 9705
1984 Edition General Rules for Emission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 10795
1984 Edition Insulation Resistance Testers (Magneto Generator Operated) 絕緣電阻計（發電機式） |
|
|
|
CNS 11151
1984 Edition Method of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 4662
1984 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 10502
1984 Edition Method for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 10225
1984 Edition Test Code for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 4658
1984 Edition Tommy Screws with FixeD Clamping Bolt 貫頭螺釘（固定扳桿型） |
|
|
|
CNS 6409
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 6408
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 4664
1984 Edition Closed Insert Nuts with Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 5030
1984 Edition Projection Welding Machine 凸壓電焊機 |
|
|
|
CNS 5028
1984 Edition Rectifier Type DC Arc Welding Machines with Drooping Characteristic 穩流整流式直流電弧電焊機 |
|
|
|
CNS 4663
1984 Edition Closed Insert Nuts with Disk for Plastics Mouldings 嵌入螺帽（片封式，嵌於塑膠製品內） |
|
|
|
CNS 10911
1984 Edition Method of Test for Microswitches 微動開關試驗法 |
|
|
|
CNS 11156
1984 Edition Grease Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 6411
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 6410
1984 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 4660
1984 Edition Tommy Nuts with FixeD Clamping Bolt 貫頭螺帽（固定扳桿型） |
|
|
|
CNS 11153
1984 Edition Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar 細粒料中有機物對水泥砂漿強度影響試驗法 |
Translated |
| Find out:13340Items | To Page of: First -Previous-Next -Last | [418] [419] [420] [421] [422] [423] [424] |
