"D C " CNS Standards List| Resin flux | Method test | Boat Deck | Engineering Drawing | Electric motor | Methods measurement | N,N | Control Cables | |
|
CNS 2227
1984 Edition Low-Voltage Cartridge Fuses 低壓配線用筒型熔線 |
Translated |
|
|
CNS 6777
1984 Edition Indoor Post Insulators 屋內柱形絕緣體 |
|
|
|
CNS 11160
1984 Edition Octave and Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及1/3八音度頻帶分析器 |
|
|
|
CNS 11094
1984 Edition Non-Thread Terminals 無螺紋端子 |
|
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and SheateD Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 11040
1984 Edition Method of Conical Cup Test 錐杯試驗法 |
|
|
|
CNS 10899
1984 Edition Method of Test for Flat Quick-Connect Terminals 平板型接頭檢驗法 |
|
|
|
CNS 2900
1984 Edition Polyvinyl Chloride InsulateD Copper Wire 聚氯乙烯絕緣屋內電話線 |
Translated |
|
|
CNS 11162
1984 Edition Metal Sheathed Thermocouples 金屬被覆熱電偶 |
|
|
|
CNS 2943
1983 Edition Screwed Type Malleable Cast Iron Pipe Fittings 螺紋式展性鑄鐵管件 |
Translated |
|
|
CNS 8763
1983 Edition Method of Test for Micro Hardness Testing Machines for Vickers and Knoop Hardness 微小硬度試驗機檢驗法－維克氏硬度及克諾普硬度 |
|
|
|
CNS 8214
1983 Edition Testing Method of Outside and Inside Diameters Wrapped Bushes for Plain Bearing 滑動軸承用捲製軸承襯檢驗法(外徑及內徑) |
|
|
|
CNS 4107
1983 Edition Flat Seal for Hydraulic Couplings 液壓接頭用扁封 |
|
|
|
CNS 3132
1983 Edition Hexagon Nuts with Small Widths Across Flats 小六角螺帽（機動車工業用） |
Translated |
|
|
CNS 5059
1983 Edition Supporting Pin and Locating Pin 支座銷與定位銷 |
|
|
|
CNS 10643
1983 Edition Curved Lip, Fluted Jaw, Blacksmiths Tongs 鍛工用有槽顎夾夾鉗 |
|
|
|
CNS 4693
1983 Edition Fish Bolts with Round Head and Oval Neck 魚尾板螺栓（具圓頭橢圓頸） |
|
|
|
CNS 4653
1983 Edition Slotted Headless Screws with Full Dog Point 有槽無頭長柱端螺釘 |
|
|
|
CNS 10644
1983 Edition Rivet-holding Blacksmiths' Tongs 鍛工用鉚釘夾鉗 |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 4696
1983 Edition Round Head Nip Bolts 圓頭單鰭螺栓 |
|
|
|
CNS 173
1983 Edition Key Section and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
|
|
CNS 4946
1983 Edition Clamping Screws for Drawing Instruments 製圖儀器用夾緊螺釘 |
|
|
|
CNS 4652
1983 Edition Slotted Headless Screws with Chamfered End 有槽無頭去角端螺釘 |
|
|
|
CNS 172
1983 Edition Woodruff Keys 半圓鍵 |
|
|
|
CNS 4654
1983 Edition Hexagon Set Screws with Full Dog Point 六角頭長柱端固定螺釘 |
|
|
|
CNS 10150
1983 Edition Test Code for Accuracy of Vertical Multi-Spindle Drilling Machines 立式多軸鑽床之精度檢驗標準 |
|
|
|
CNS 167
1983 Edition Double Tangential Keys 雙切線鍵 |
|
|
|
CNS 168
1983 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 169
1983 Edition Flat Fitting Keys and Sliding Cotter 配合平鍵及滑鍵 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [420] [421] [422] [423] [424] [425] [426] |
