"D C " CNS Standards List |
|
CNS 4262
1983 Edition Method of Life Test for Single Point Carbide Tools 碳化物車刀性能試驗方法 |
|
|
|
CNS 3132
1983 Edition Hexagon Nuts with Small Widths Across Flats 小六角螺帽（機動車工業用） |
Translated |
|
|
CNS 10237
1983 Edition Handles for Cranes 起重機用手柄 |
|
|
|
CNS 173
1983 Edition Key Section and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
|
|
CNS 10311
1983 Edition Method of Test for Vending Machine 自動販賣機檢驗法 |
|
|
|
CNS 7959
1983 Edition Method of Test for Stationary Governor Type Tachometers 固定調速式轉速計檢驗法 |
|
|
|
CNS 171
1983 Edition Screw and Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 4691
1983 Edition Studs for Stud Welding With Tip Ignition; Threaded Studs 尖端燃熔用螺樁 |
|
|
|
CNS 168
1983 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 10683
1983 Edition Round Steel Chains Without Quality Requirements 圓鋼製環鏈（不涉及品質要求） |
|
|
|
CNS 10605
1983 Edition Condenser Type Spot Welding Machines 電容式點焊機 |
|
|
|
CNS 10643
1983 Edition Curved Lip, Fluted Jaw, Blacksmiths Tongs 鍛工用有槽顎夾夾鉗 |
|
|
|
CNS 10644
1983 Edition Rivet-holding Blacksmiths' Tongs 鍛工用鉚釘夾鉗 |
|
|
|
CNS 10646
1983 Edition Double-Pick up, Blacksmiths' Tongs 鍛工用雙葫蘆形夾鉗 |
|
|
|
CNS 10647
1983 Edition Gad, Blacksmiths' Tongs 鍛工用尖鏨平口鉗 |
|
|
|
CNS 10648
1983 Edition V Shaped Blacksmiths' Tongs 鍛工用Ｖ形夾鉗 |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 10601
1983 Edition Method of Test for Hinge Type Electromagnetic Relays 鉸鏈型電磁電驛試驗法 |
|
|
|
CNS 5057
1983 Edition Feet with Thread for Jigs and Fixtures 具螺紋柄支腳（夾具用） |
|
|
|
CNS 4653
1983 Edition Slotted Headless Screws with Full Dog Point 有槽無頭長柱端螺釘 |
|
|
|
CNS 4646
1983 Edition Square Taper Washers for High Prestressed I-Sections 斜墊圈（工字鐵高強度結構用） |
|
|
|
CNS 8763
1983 Edition Method of Test for Micro Hardness Testing Machines for Vickers and Knoop Hardness 微小硬度試驗機檢驗法－維克氏硬度及克諾普硬度 |
|
|
|
CNS 4606
1983 Edition Studs, Metal End≈2.5d 螺樁（旋入端長～2.5ｄ） |
|
|
|
CNS 4652
1983 Edition Slotted Headless Screws with Chamfered End 有槽無頭去角端螺釘 |
|
|
|
CNS 4945
1983 Edition Adjusting Screws for Drawing Instruments 製圖儀器用調整螺釘 |
|
|
|
CNS 5059
1983 Edition Supporting Pin and Locating Pin 支座銷與定位銷 |
|
|
|
CNS 4607
1983 Edition Studs for T-Nuts 螺樁（Ｔ形螺帽用） |
|
|
|
CNS 4946
1983 Edition Clamping Screws for Drawing Instruments 製圖儀器用夾緊螺釘 |
|
|
|
CNS 4647
1983 Edition Square Taper Washers for High PrestresseD Channels 斜墊圈（槽鐵高強度結構用） |
|
|
|
CNS 5058
1983 Edition Setup Blocks Adjustable Type 可調整組合墊塊 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [422] [423] [424] [425] [426] [427] [428] |
